Search:

Steve,

I've used the sliding table for a few years. I wouldn't want to be without it. I've seen some people complain that there's play in the fence mounting. Yes, there is but there's an easy way...

Pm sent.

Cliff

Pat,

Put a couple of 2 x 10s in the bed. Have Woodcraft lay the saw on its side on the boards near the cab. When you get home pull the boards and saw out the back until the boards tip and the saw...

Pulling this thread back up since there recently were questions by a few people on how to adjust the tables on a Hammer A3-31. Posts 21-25 by Brian Arbuckle have the best instructions I've ever seen....

October 2022. List price $599.

I'm considering adding some miter spring clamps for frames and small moldings. I've never used them before and wondered what's the best way to deal with the holes they leave?

Thanks
Cliff

The fence is sold.

Very lightly used Veritas shooting board fence.

Build your own shooting board with adjustable angles.

Fixed detents at 0°, 18°, 22.5°, 25.7°, 30°, 36°, 45° and 60° with a microadjust to let...

I've got a Rotex 125, an ETS 125 and a Rotex 90.

The Rotex 125 is for heavy sanding. The ets is for finish sanding. The Rotex 90 is for detail sanding with the triangle pad or pieces too small for...

I just got a shipping notice for a Veritas 1/2" PM-V11 chisel that was ordered last September, so there's hope yet.

That's the last one to fill the set.


Cliff

If you think about it, where the blade is in relation to the crown of the tire affects the angle of the blade to the wood.

When I put a new blade on my saw I take a hunk of plywood and slice off...

If that's an Incra Ultra I sold one last August for $150.

Cliff

Eric,

I recently upgraded a Shop Fox 2 hp model to an Oneida v-3000 3hp along with new, more extensive ductwork. It made a big difference and I'm very pleased with the results.

Cliff

Joe,

I recently put in a new Oneida V-3000 DC and new ductwork. I did the first draft of the design then sent it to Oneida to refine it. It took a couple back and forths but in the end they did a...

Anibal,

I just did this and can send you the documentation. I tried to send you a pm but you're member status. If you upgrade to contributor status (it's only $6 a year) we can talk this over.
...

Sorry for taking so long to update. Had a lot of things going on over the weekend.

Machine is all dialed in and is jointing beautifully. Discovered I need to be more diligent with moving the fence...

Edwin.

Started noticing tapered cuts. The machine's 8 years old so not surprising it could use a tune up. Figured it was a good time to rotate the inserts while I was at it, which went well. If...

Does anyone have any fairly recent documentation on adjusting the jointer tables of a Hammer a3-31 detailing the steps in order? The only thing I have is one from 2014 that describes the general...

Pm sent for 1/2" bench chisel.

Cliff

6 Veritas Bevel Up Plane blade cases. $18 shipped in a small flat rate box.

476231

Tom,

If you're talking about the Mas-R-Lift ll it will handle a number of routers without adapters. I had a Dewalt 618 in one then switched to a Milwaukee 5625. The lift adapted to both.

Cliff

The issue is in putting it back together. Hide glue will adhere to hide glue so you can just add new glue. PVA glue doesn't adhere to itself, it needs fresh wood so you have to remove all the old...

Ronald,

The bushing is used to guide the drill bit, not to be placed in the dog hole. You only need one.

Cliff

Derek,

My saw has the door switches, and it also has a switch on the blade tension release. If the blade isn't tensioned the motor won't start.

Try putting a blade on, tension it and see if it...

Does anyone know where I can get a base for the Ridgid cordless trim router? I've searched and can't seem to find one. I also have a Bosch colt and have made a few jigs for it and it's convenient to...