Search:

Type: Posts; User: brent stanley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. I'm pretty sure the stock for the actual floor...

    I'm pretty sure the stock for the actual floor (this was a scrap used for testing) is without blue stain, but I do think this looks quite nice!
  2. Decided to make the second floor "spline and...

    Decided to make the second floor "spline and groove" instead of traditional tongue and groove. Makes for a more interesting joint where it is visible. Decided to get some dedicated tooling to...
  3. I have been using the Heritage Natural Finishes...

    I have been using the Heritage Natural Finishes products the past few years for my interior and exterior products and really like it so far. The underside of my gable end overhangs will have fake...
  4. I normally do what Jared does too. Was a time...

    I normally do what Jared does too. Was a time when I used to do chip loading calculations and all that jazz, but now that I have done that a bunch I just make sure the machine settings are to...
  5. Haha! Not sure my tractor would lift it, so...

    Haha! Not sure my tractor would lift it, so I'll have to pass. I do have a lovely Buffalo 18" that is a delight to use!

    B
  6. So to resurrect a thread from the catacombs.... ...

    So to resurrect a thread from the catacombs....

    This project is carrying on. I ended up inches from needing spinal surgery so I had to shut down for a long time. It was a bad time....

    Then as...
  7. Replies
    4
    Views
    730

    Hi Tom, no it's a manual push/pull style like a...

    Hi Tom, no it's a manual push/pull style like a giant radial arm saw. I hope I get it back up and running because it will be a tremendous help. The plan now is to set up my lathe and vertical...
  8. Replies
    4
    Views
    730

    Radial Arm Saw tooling

    It's great to see a bit of a resurgence of the Radial Arm Saw with folks buying big old machines and putting them back into service. I have two of them, a 14" Wadkin BRA and a huge 18" beast that is...
  9. Replies
    27
    Views
    2,191

    Look into Accoya. Machines very well and takes...

    Look into Accoya. Machines very well and takes paint very well. I've been experimenting with it and it works quite well. Jointed a board flat 2 years ago and it's still "suction to the jointer...
  10. Very interesting, thanks Kevin. I would assume...

    Very interesting, thanks Kevin. I would assume it could be adjusted out if required, but I do recall the issue being discussed here in the past I just can't seem to find it with the clunky search...
  11. He he.....top secret so far! Negotiations are...

    He he.....top secret so far! Negotiations are underway but it will weigh more than my wife's car. :D

    Thanks Phillip, I'd kind of thought of those as potential solutions, and I think the copes...
  12. In-table sliders for shapers - 0.5mm lip?

    My shapers don't have an integral sliding table, built into the main table. I just use bolt on versions and my new machine will have a side mounted version, but I'm wondering how folks deal with the...
  13. Replies
    35
    Views
    3,596

    Wow. If you don't have a grinder system, is it...

    Wow. If you don't have a grinder system, is it at all practical to do the sharpening at home or will you be looking to send them out for sharpening? And if you are sending them out for sharpening,...
  14. Very interesting, I enjoyed that, thank you, B

    Very interesting, I enjoyed that, thank you,

    B
  15. Replies
    35
    Views
    3,596

    Hi Kevin, here is a video my Mark Hennebury...

    Hi Kevin, here is a video my Mark Hennebury talking about a dedicated machine for the job, though I expect this may have been the Rolls Royce approach.
    ...
  16. Replies
    102
    Views
    9,603

    Brian, could I bother you to take a picture of...

    Brian, could I bother you to take a picture of the insert style knife system you upgraded to? I'm really curious about it. Thank you,

    Brent
  17. Replies
    102
    Views
    9,603

    Wow! I'd never imagined using it for millwork,...

    Wow! I'd never imagined using it for millwork, but the argument is sound! Thanks, now I want one even more!
    I really prefer a planed or scraped surface to a sanded one and the SS would really...
  18. Replies
    102
    Views
    9,603

    Some day when I grow up I would like to have a...

    Some day when I grow up I would like to have a super surfacer ...
  19. Replies
    102
    Views
    9,603

    If you can hunt around and find some additional...

    If you can hunt around and find some additional pics of it, the scope and scale of it will blow your mind. Someone said it was the largest outdoor timberframe built in the last 100 years or...
  20. Replies
    102
    Views
    9,603

    Hi Brian, those sizes are exactly what I was...

    Hi Brian, those sizes are exactly what I was thinking would suit a RAS very well. I am incorporating more Japanese approaches , styles and joinery into my work all the time. Our house will be very...
  21. Replies
    102
    Views
    9,603

    Exactly, now if you could get an 800lb timber up...

    Exactly, now if you could get an 800lb timber up on the benches in front of the saw it may have enough weight to stay put and maybe wouldn't matter so much if you're not doing a thru cut, but in the...
  22. Replies
    102
    Views
    9,603

    Brian, timberframing is one of the things I do...

    Brian, timberframing is one of the things I do for a living and very few shops use RASs at all, and if they do it's for small stuff like braces, struts or extremely small members like truss...
  23. Replies
    102
    Views
    9,603

    Oh really? I'm aware of the pros and cons of the...

    Oh really? I'm aware of the pros and cons of the different styles, but what are the pros to a turret style that win you over?
  24. Thanks Rob, after looking up Interlock (thank you...

    Thanks Rob, after looking up Interlock (thank you for that, looks promising) I went down the Assa Abloy rabbit hole and that was quite a place! They have a lot of subsidiary companies!
  25. Replies
    36
    Views
    2,681

    Someone needs to buy one of those and report back...

    Someone needs to buy one of those and report back to tell us what they think!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4