Search:

Type: Posts; User: Timothy Orr; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    1,120

    I’d suggest renting a set of rol-a-lifts. You...

    I’d suggest renting a set of rol-a-lifts. You strap them to opposite sides of the machine and you should be able to better balance the machine than on a pallet jack.

    456114
    you might have to...
  2. Replies
    32
    Views
    1,837

    If you can pick it up from the freight terminal...

    If you can pick it up from the freight terminal and they’ll load a trailer at ground level, rent a drop deck trailer like this:
    456112...
  3. Replies
    71
    Views
    8,245

    I agree that this is the key issue. ...

    I agree that this is the key issue.

    Specifically if zinc parts are used as in the example given by John. Zinc alloys are very susceptible to creep. For the technically inclined here is a link to...
  4. Replies
    12
    Views
    1,536

    The AFCI breakers in my house have a LED that...

    The AFCI breakers in my house have a LED that flash a code to tell you why it tripped. Might look to see if yours have that feature. I had to search for the manufacturer’s spec to find out how to...
  5. Forrest can replace teeth and even straighten if...

    Forrest can replace teeth and even straighten if needed. Had them do so after an activation (miter gauge). It wasn’t free but less than the cost of a new blade. Here’s the menu of services and...
  6. Hey Rick, Any luck? I've also always wanted...

    Hey Rick,

    Any luck? I've also always wanted to build a machinist chest so was interested to see if you were able to find the plans.

    Tim
  7. It is listed in the Aircraft Spruce US catalog,...

    It is listed in the Aircraft Spruce US catalog, look at page 833 here: https://www.aircraftspruce.com/pdf/index.html

    You might call or email them. Their e-commerce site may not be completely...
  8. Here’s another way to think about it. The rusted...

    Here’s another way to think about it. The rusted surface certainly isn’t as precision as it was pre-rust, and it may not even be functional if moving parts are involved. So you sort of have no choice...
  9. Replies
    15
    Views
    1,147

    I would think a reamer would be the way to go to...

    I would think a reamer would be the way to go to take off the .25mm or so. You can get a 20mm reamer or an adjustable one. They make hand held ones or you could use a power drill, but would probably...
  10. Hot melt glue gun

    Hot melt glue gun
  11. Replies
    20
    Views
    1,913

    I have the small one. I like it. Easy to use and...

    I have the small one. I like it. Easy to use and control. I used it to clean up veneer seams. Have not had to sharpen it yet as the edge seems to hold up well. I intend to buy the larger ones when I...
  12. Replies
    32
    Views
    2,638

    Here's a similar knot I filled on a walnut coffee...

    Here's a similar knot I filled on a walnut coffee table. Used System Three T88 with a couple of drops of dark brown Transtint dye. Overfilled it slightly then planed/scraped it flush. I think it...
  13. Anther idea would be build a dedicated machine....

    Anther idea would be build a dedicated machine. Gang mount 8 routers to a platform that will plunge down then move the platform following a template. You could cut all 8 out of your sheet at once. ...
  14. Replies
    20
    Views
    2,085

    Could you build it up from 1/4” pieces instead? ...

    Could you build it up from 1/4” pieces instead? Rather than remove the dado, add two 27/32” wide 1/4” thick strips spaced 1-5/16” apart to the base piece of 3” wide 1/4” thick material, nail or glue...
Results 1 to 14 of 14