Search:

Type: Posts; User: Scott Clausen; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    24
    Views
    634

    The D-mark has some carbon surge protectors that...

    The D-mark has some carbon surge protectors that are still "in line" even with the house phones disconnected. Unless the cable has failed that is where your hum is coming from. Should be a free telco...
  2. Looks like you did a fine job there.

    Looks like you did a fine job there.
  3. Replies
    11
    Views
    507

    Video is very demanding on SD cards. I use these...

    Video is very demanding on SD cards. I use these in Alarm.com cameras because they one of three types that are tested to work. They come in 128 GB and 256 GB. I have no idea if they are needed for...
  4. Could be splitting hairs here but a floating...

    Could be splitting hairs here but a floating tenon will not likely have a bond on either end and may even have a gap on one or both mortise bottoms. A normal tenon will have a firm solid connection...
  5. The reason many groups leave and start their own...

    The reason many groups leave and start their own forums and the reason the OP hates it are the same. Facebook deliberately makes it difficult to search and get back to a post you have already seen....
  6. Replies
    21
    Views
    1,540

    Derek, I have been going through ways to hide the...

    Derek, I have been going through ways to hide the ploughed groove for the panels. Watched a video (Rob Cosman) on four ways to hide. Cutting the last pin at 45 deg was not one of them. Thank You!
  7. Beauty marks they are.

    Beauty marks they are.
  8. Haven't watch a game since I saw a player take a...

    Haven't watch a game since I saw a player take a knee during the anthem. Calling me a racist every time they have a free moment and inventing an alternant anthem won't get me back either. I have much...
  9. BLO here because its only there till the next...

    BLO here because its only there till the next flattening anyway. I like the flat non-slick feel.
  10. I think the most likely use is sung to the tune...

    I think the most likely use is sung to the tune of "your cheating heart"
  11. Replies
    54
    Views
    3,985

    Oh how I remember, I bought my first house and...

    Oh how I remember, I bought my first house and was in a hurry to lock in at 15% before rates went up.
  12. Replies
    54
    Views
    3,985

    The manufacturing cost increases are here to...

    The manufacturing cost increases are here to stay. I suppose the shipping cost could retreat some in the future but that is a crapshoot at best. To those that think inflation is 7% are dreaming. Some...
  13. Replies
    26
    Views
    4,279

    Zombie treads always get me. I look for awhile...

    Zombie treads always get me. I look for awhile and then get slack about it. Thanks!
  14. Replies
    26
    Views
    4,279

    When I carry too much extra weight all kinds of...

    When I carry too much extra weight all kinds of bad things appear. Insomnia, snoring. high blood pressure and back pain. It takes a lot of work to lose the weight but it can be done. I have tried...
  15. I think on a smaller plane the risk of rounding...

    I think on a smaller plane the risk of rounding the bottom is significant. On a larger plane I don't think it is required unless it is really whacked out. That said when I do a full restoral and want...
  16. Yeah, the truth lies somewhere in between but...

    Yeah, the truth lies somewhere in between but this after all, a sharpening thread. It doesn't take long to go off the rails.
  17. I agree, I am just trying to get a sharp edge...

    I agree, I am just trying to get a sharp edge that I can use for a task. If I must inspect with a scanning electron microscope to confirm if it is the sharpest on earth, it takes some of the fun out...
  18. I had a 6" jointer but found that a board in bad...

    I had a 6" jointer but found that a board in bad shape, I could easily remove a huge amount of wood attempting to get a flat face. If I take a hand plane I can work the board into much better shape...
  19. Replies
    11
    Views
    898

    Won't fit your bench/cart but the Saw Stop...

    Won't fit your bench/cart but the Saw Stop jobsite saw is worth a look. Roll cart, accurate, table is a bit larger than most contractor saws and the safety feature if that is a desire. I am in a...
  20. Replies
    43
    Views
    2,679

    If I ever get that "slow start" I go to the store...

    If I ever get that "slow start" I go to the store and get a new one. My company vans drain quickly due to the trackers. I was reading up on the new ones and they have a idle time cut off so maybe...
  21. Replies
    43
    Views
    2,679

    Most manufacturers don't put the "Best" batteries...

    Most manufacturers don't put the "Best" batteries in production cars. Even if they do anyone can get the bad one.
  22. Replies
    15
    Views
    1,264

    That's a great idea, I intend to blow them off...

    That's a great idea, I intend to blow them off but too lazy to wait for my leaky air compressor to charge up. I am gonna get me one to hand on the side of the plane till.
  23. Replies
    12
    Views
    1,080

    I was practicing DT for a while but got...

    I was practicing DT for a while but got distracted by some projects. This thread makes me want to get back to it.
  24. Replies
    49
    Views
    2,707

    A couple of things come to mind here. Buying...

    A couple of things come to mind here. Buying paper products in bulk means you need to store them too so storage space is something to account for and the savings won't likely justify it. As stated...
  25. I use a shop vac with a cyclone. Best I can say...

    I use a shop vac with a cyclone. Best I can say is it is better than nothing. It has trouble keeping up with my DW735 unless I start empty. I am thinking about building a "dust house" on the back or...
Results 1 to 25 of 203
Page 1 of 9 1 2 3 4