What is the condition of the tires on the saw?
I saw big vibration improvements on a 14” Delta clone I had after replacing the old rubber tires with urethane tires.
Type: Posts; User: Jay Norton; Keyword(s):
What is the condition of the tires on the saw?
I saw big vibration improvements on a 14” Delta clone I had after replacing the old rubber tires with urethane tires.
Jim/John,
Thanks for the feedback. Honestly, it was what I expected, don’t worry about the manufacturer specs, just go by the actual product in hand. Just trying to learn all I can .. ;)
...
Is there a reliable source for a viscosity conversion chart/calculator out there?
I am entering the spray finish world. I bought a quart each of Target Coatings EM2000 & EM6000 in satin.
...
Aaron,
I agree the Cosman micro-bevels could be challenging, especially since they are likely done without a jig.
The Charlesworth ruler trick may be easier, as the new user can fairly easily...
Echoing what Jim said…
Here is a link to an old Charles Neil video about trace coating to enhance figured wood.
https://youtu.be/mjTSIiUiEOI?si=ksiDrXjPO672rnOQ
I haven’t really compared their prices to anywhere else, but I like their Rhynogrip hook & loop discs
https://www.industrialabrasives.com/
Karl,
The spacers I used are 1/2” OD x 1” long. Bolts are 3/8”.
I am happy so far with the solution and the position.
I opted to keep the rail flush with the right edge of the table as I...
Well said. Agree 100%
I have purchased a couple large machines at Woodcraft. Both were shipped free to the store (I ordered in store). I picked both up at the store. They loaded them into my truck.
https://www.industrialabrasives.com/58-hole-assortment-rhynogrip-hook-loop-discs-01950-p-1386.html?zenid=h03n3104r1mpuj7smh0n7mtgj3
Does anyone recognize the markings on this chisel? Curious of the origin/manufacturer…
I have 3 with similar markings. This is the only visible lettering on the chisel.
505294
I was questioning if drilling the hole would distort the metal.
He recommended hanging as an alternative to horizontal (properly supported)
I gave Starrett a call and spoke to a tech. He said drilling a hole in the end would not affect the accuracy.
Agree, hanging is a good storage method.
My question is does drilling a hole in a steel/aluminum straight edge have any affect on accuracy?
I have had good luck with Krud Kutter (the red bottle) cleaner/degreaser
Has anyone drilled a hole in their straight edge for hanging/storage?
Did it affect the accuracy?
I put a coat on the underside/no show surfaces today.
All surfaces primed with 2 coats Zinsser BIN, lightly sanded with 320
SW Pro Classic acrylic satin
thinned ~5% with water (1.5 oz in 1 qt...
Which Laguna did you buy? Interested if anyone has tried the Quadtec 8”/1.75 HP 110v
Small world. I went to college at Alfred State. I live in PA now, but get up to the Alfred area quite often to hunt.
John, Thanks!
What general part of Western NY are you located?
I grew up in Steuben County.
Jay
Greg,
I designed it. Here are the rough dimensions.
The height is ~22”. The top is 14 3/4” x 42”. Shelves have 7 1/2” between them.
Jay
I tried a sample piece with 2 coats spray Polycrylic. It definitely darkened the 2 coats of white primer under it. Polycrylic on left side
499515
I am leaning towards using ProClassic without...
Jeff,
Is Minwax Polycrylic considered “water white”? It is advertised as non-yellowing. I believe I recall it being milky white in the can.
Jeff & John, thanks for the info, very helpful