What are your recommendations? I have found that some, in the past, are bad about plugging the nozzle so any that you have experienced in that regard get a go to the front of the line pass. Thanks
Type: Posts; User: tim walker; Keyword(s):
What are your recommendations? I have found that some, in the past, are bad about plugging the nozzle so any that you have experienced in that regard get a go to the front of the line pass. Thanks
Thanks, looks like conventional rails which is what I have but on a Bosch. Mine is also a compound beveled so I have to take that into account. How far out does your table extend to account for the...
Tom, how deep are those drawers? Mine will be 24" deep w full extension, soft close slides.
I have Sketchup Pro 2022. Way more than I need but that is what I have. I am drawing some cabinet drawers of varying heights and want to have each drawer height on a different page or tab so that...
I have used the software previously and it does a good job, but all the work was with 3/4" stock. Has anyone used it on a combo 3/4" and 1/2" ply design or do I need to generate two different cut...
Thanks Jim, 1/2" 12 mm it is.
Is 1/2" drawer carcass with 3/8 or 1/2" bottoms good for drawers that are medium duty service, 29" wide and 26" deep? 3/4 ply is $49/sheet and 1/2" is $27.89 at my local distributor(Dakota...
Inside dimensions will be 32.5" tall (changeable) and 30" wide. Side mount self-closing drawer slides at 1/2" thickness each, so the outside dimension of the drawer will be 29" and the slides are...
I am building some shop cabinets that will be 30" wide, so with side mount slides, each drawer will be 29" wide. I will alter install overlay drawer fronts as there will be no face frame. I want...
Shop cabinet. The cabinet will have about 5 drawers. Intuitively my engineering degree says place base so that it supports the weight from the drawers. The stretchers would be inside the sides at...
CabinetSense no longer works with older versions, only 2019-23. I have 2023 hard drive version and it is available for download. Here is the screen capture. 514839
Good idea on teh wood pieces Zachary. I 'll try that methodology first.
Shop cabinets for a miter saw station. Is 38" too high for the counter top? 3" toe kick, 33" cabinet box. 1.5" top. I am 6'6" tall and the distance from the floor to my forearm bent at 90 degrees...
Forgot Pocket hole Screws (with or without glue)
Another drawer construction question - Building preferences = Butt joint with glue and screws, dados with G&S, Dominos with G&S, or a 45° Lock Miter Router with glue? TIA
For lighter drawers(or drawers that may only have screwdrivers or pliers, is it ok to to just use a rabbit and 1/4" ply screwed and glued to the bottom or would you still use a dado unglued?
Mike, how deep are your drawers and what bottoms did you use, 1/4 or 1/2"
Good questiona s tat is the actual cutting area.
I am building a couple of side-by-side cabinets for the shop. They will be 30" wide. The space between the top and bottom inside will measure 34". Should I make all the drawers the same thickness...
I am doing some maintenance and fine-tuning. I have a 3 hp SawStop PCS with a 52" rail system. What is the acceptable runout tolerance for the T Fence? Mine is currently registering 0.005" toe...
About to start building base cabinets for the workshop. Will use a separate base and level that, then install cabinets on top. The cabinets will be all drawers, no doors, and approximately 30" wide....
My Bosch 4410 Dul Bevel SCMS cuts a max of 52 deg right and 60 degrees left. The 4410 is an older saw that has rails in the back so it requires significant space behind the saw. I am building a...
Yes I agree on the metric. The last project I did was in metric. it is SO much easier, for instance, if I need to divide 17 13/15 by three. its much easier to divide 454 mm by 3 for151.3 mm or...
Designing a shop project using 3/4" ply which is really 18 mm (0.708"). When using Sketchup for your design, do you use 0.708" or do you use 0.750"? These cabinets will span approximately 12 ft.
So for shop cabinets, toe kicks or no toe kicks? I am building a variation of Jay Bates miter station and he did not have toe kicks but then he only had 9” of flat countertop available so that may...