Search:

Type: Posts; User: Darcy Warner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. I would pull outfeed table and clean those...

    I would pull outfeed table and clean those surfaces, however I wouldn't fight try it too much.

    Rarely do I use a setting gauge on a jointer, just a small board with two pencil Mark's. That...
  2. Replies
    1,089
    Views
    90,132

    Last one I weighed was 3350.

    Last one I weighed was 3350.
  3. The best, small quiet compressor I ever owned is...

    The best, small quiet compressor I ever owned is my 12 year old makita. It has been beat to death, never changed oil, great compressor.
  4. Like Jim said, I have a big shop. I did luck out...

    Like Jim said, I have a big shop. I did luck out and the entire thing was hard piped for air. Main line is 2" and probably 200 feet long.

    When I get everything hooked to air, I may not have...
  5. My 200 gallon quincy 390 never gets turned off. ...

    My 200 gallon quincy 390 never gets turned off.

    Not filling that tank and 500 feet of hard lines all the time.

    Fuses in the disconnect and heaters in the starter protect the motor.
  6. Just open the door to the electricals, be real...

    Just open the door to the electricals, be real easy to identify which two wires feed the control transformer, which are also fairly easy to identify.
  7. I don't see that, from the post i can tell they...

    I don't see that, from the post i can tell they are at least smart enough to know that you don't want to hook the generated leg to the control circuit.
  8. Figure out what two wires run the control...

    Figure out what two wires run the control transformer and don't hook it to those two.
  9. Replies
    30
    Views
    1,120

    It was just the next increase in supply voltage,...

    It was just the next increase in supply voltage, it's the era of 230/460v motors. Not sure when the bump to 240/480 started.

    No matter what though, 10% either way is fine for a motor.
  10. Replies
    30
    Views
    1,120

    I have plenty of motors that say 110v and 220v. ...

    I have plenty of motors that say 110v and 220v.

    That was supply voltage back 70 years or so, as demand got bigger, supply voltage was bumped up, 115v 230/460
    Now we are at 120 240/480
  11. Replies
    30
    Views
    1,120

    Uh, what brings you to that conclusion? I can't...

    Uh, what brings you to that conclusion? I can't remember the last time I saw a 440v single phase motor on anything.
  12. Replies
    30
    Views
    1,120

    I was told about 125 pounds each. Originally it...

    I was told about 125 pounds each. Originally it was set up with a chain fall to remove discs to glue new paper on them.
  13. Replies
    30
    Views
    1,120

    My 37" dual disc Oliver takes 90 minutes to stop...

    My 37" dual disc Oliver takes 90 minutes to stop if I turn off the braking on the vfd.
  14. Replies
    30
    Views
    1,120

    That t17 had no original parts.

    That t17 had no original parts.
  15. Replies
    14
    Views
    934

    It's called redundancy, like having 4 or more...

    It's called redundancy, like having 4 or more shapers set up, a couple moulders, 3 tenoners, etc. If a person has the need and work for pin routers, having multiples set up for different tasks,...
  16. Currently 6 NF sitting in my shop ranging from...

    Currently 6 NF sitting in my shop ranging from the early 50s to to the late 70s. All still in their original grey.

    Shaper, 4 unipoints, a 12" jointer and a #4.

    Hold it, how did #7 slip in?
  17. Replies
    14
    Views
    934

    Yeah, pin routers are still big money makers in...

    Yeah, pin routers are still big money makers in the right environment. the R9s were the top of the heap. I have two with tilting heads, vacuum hold downs, power feed and tables that move for under...
  18. Replies
    14
    Views
    934

    Except I can buy 20+ scm R9s and have each one...

    Except I can buy 20+ scm R9s and have each one pounding out parts. A pin router is an awesome machine in the right hands.
  19. My least favorite part of NF jointers is the...

    My least favorite part of NF jointers is the bracket for the gaurd. My favorite is the porter as it can easily drop down out of the way.
  20. That's original paint. They made the switch from...

    That's original paint. They made the switch from stock grey to green in the late 70s early 80s I believe.
  21. Yes, a few. Old head gets sent in, they measure...

    Yes, a few. Old head gets sent in, they measure and copy.
    Hermance is my go to for heads.

    I do what my customers want, but I see no need for them in a jointer.
  22. Jeff is the owner. Wonderful guy.

    Jeff is the owner. Wonderful guy.
  23. I went from an 8" oliver (I miss that jointer),...

    I went from an 8" oliver (I miss that jointer), to a 16" fay and egan 316 (that one was nice too) to a 20" Clement (I miss that one too) to a 30" American. With about every manufacturer and width...
  24. Replies
    16
    Views
    510

    The best tips have always been the ones that come...

    The best tips have always been the ones that come with my GRK screws. Whia a close second.
  25. Replies
    16
    Views
    510

    Been buying the Milwaukee impact bit sets, I...

    Been buying the Milwaukee impact bit sets, I loose the bits before I break anything
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4