Search:

Type: Posts; User: Steve Jenkins; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. Easiest would be to advance the hours 12

    Easiest would be to advance the hours 12
  2. Replies
    5
    Views
    386

    That’s what I saw

    That’s what I saw
  3. Replies
    23
    Views
    1,146

    Walnut will do that if your hands are sweaty

    Walnut will do that if your hands are sweaty
  4. It looks like you are tipping the sander a little...

    It looks like you are tipping the sander a little bit or putting more pressure toward one side. That’s about all I can think of that would cause that effect with all the sanders
  5. Replies
    37
    Views
    1,639

    Agree on the Keller. Used the 16”er for years...

    Agree on the Keller. Used the 16”er for years until I ran across a like new Exrema single spindle for 500.00.
  6. Replies
    4
    Views
    554

    Just thought I’d give this a bump

    Just thought I’d give this a bump
  7. Replies
    4
    Views
    554

    Good idea Jim. Did that after you suggested it.

    Good idea Jim. Did that after you suggested it.
  8. Replies
    4
    Views
    554

    Should have said I’m looking to buy.

    Should have said I’m looking to buy.
  9. Replies
    4
    Views
    554

    Festool HL 850 base

    Iím looking for a base that Festool no longer makes for the 850 planer. It held the planer upside down on your bench so it could be used as a small jointer. They discontinued them about 5 years ago....
  10. By then I better have that table ready for...

    By then I better have that table ready for sanding and finish it’s due prior to Thanksgiving
  11. I plan to go. Will you be there the whole time??...

    I plan to go. Will you be there the whole time?? Be nice to meet.
  12. Replies
    11
    Views
    1,012

    One way to find out is to send me a pm and I’ll...

    One way to find out is to send me a pm and I’ll answer as soon as possible. Should be within a couple hours of when you send it.
  13. Replies
    6
    Views
    407

    Check with Certainly Woods.

    Check with Certainly Woods.
  14. Very nice. Looks like a fun job

    Very nice. Looks like a fun job
  15. Replies
    36
    Views
    1,602

    I keep mine in a vertical holster from Duluth...

    I keep mine in a vertical holster from Duluth Trading in or out of the shop. No reception in the shop so I have a land line I forward it to
  16. There might be a chain tensioner on it. It looks...

    There might be a chain tensioner on it. It looks like a piece of heavy gauge wire bent to slide on the chain and held in place with a small bolt.
  17. Replies
    15
    Views
    778

    Similar to Prashun. Two sawhorses with furniture...

    Similar to Prashun. Two sawhorses with furniture pads. Completely finish the bottom then slide it to the side so one edge is near the center of both sawhorses. Rock it up on edge and while holding it...
  18. Replies
    81
    Views
    6,630

    Only thing I can think of to save time is an hour...

    Only thing I can think of to save time is an hour glass. ��
  19. Replies
    32
    Views
    2,569

    Looking good in the shop. Enjoy

    Looking good in the shop. Enjoy
  20. Replies
    133
    Views
    14,505

    Sticky: Add me to the list

    Add me to the list
  21. Replies
    21
    Views
    2,465

    Looks great Jim. A super high gloss finish is...

    Looks great Jim. A super high gloss finish is pretty satisfying to do
  22. Replies
    16
    Views
    1,376

    I don’t know, it seems pretty succinct to me.��

    I don’t know, it seems pretty succinct to me.��
  23. Replies
    6
    Views
    539

    You can get mdf 1/8” or how about using plastic...

    You can get mdf 1/8” or how about using plastic laminate
  24. Replies
    11
    Views
    515

    If your drawer fronts are inset rather than...

    If your drawer fronts are inset rather than overlay you need to deduct the thickness of the fronts from the cabinet depth.
  25. Worked 1/2 days (due to heat) cutting on a downed...

    Worked 1/2 days (due to heat) cutting on a downed pecan tree. Almost finished. Know anyone that can use a 4í diameter trunk?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4