Keep in mind the UV protection may not be indefinite. I was told years ago UV protection is provided by a molecule in the coating that absorbs photons, but that absorbind the photon destroys the...
Type: Posts; User: Don Stephan; Keyword(s):
Keep in mind the UV protection may not be indefinite. I was told years ago UV protection is provided by a molecule in the coating that absorbs photons, but that absorbind the photon destroys the...
Just what is the process to turn a catenary curve on the outside of a bowl - constantly removing the blank to check against a hanging chain?
Make a negative cardboard pattern from a hanging chain...
Politely, I would beg to differ if the suggestion is that the resulting shape of the tool will always be the same. The mount of time each part of the cutting edge spends on the grinding wheel will...
I've never had a 1/2" bar dianeter shank be a loose fit in a 1/2" diameter drilled hole. In fact the handle has to be driven onto the shank, A tapered tang can raise questions what diameters and...
Thompson Lathe Tools said the bars are supplied to them (and presumably other tool manufacturers) slightly oversize their entire length. Before beginning the working end of tools, Thompson first...
My experience peat pots dry out to quickly, after planting in the garden if any of the pot rim remains above ground the roots dry quiickly, and I don't think after planting the roots easily penetrate...
Anyone have positive experience turning the form and base, and making paper pots for vegetable and flower seedlings? I have turned the two parts but my pots don't want to hold shape, and spring is...
I haven't found it necessary to use epoxy when installing a tool in a handle.
A bit more prep time, I purchase a good quality gloss poly pint or quart, and good quality mineral spirits that is more refined. Start with a small quantity of a 50-50 mix. Wearing disposable...
Knap and Vogt full extension drawer slides are great, have used them for decades. I would be concerned about sawdust accumulating in the drawer boxes if the top of the applied front were cut down.
Several years ago I researched the red color of flame box elder on the Internet and found a research summary that said the red was produced by the tree due to trama, and not by fungus. Every comment...
John
Are you after a particular look? Would the beeswax be for items likely to handled often? Washed?
An excellent question to take to a local woodturning group if you have one. There likely you would have an opportunity to try different sizes and nose shapes before making a decision, and likely...
John
You don't have to melt beeswax or mix it with mineral oil - you can apply it just as Mr Raffan demonstrates. Note he applies some pressure on his waxy sock to melt the beeswax rubbed on the...
I've found holding a damp sponge against the tire for 5 or 6 rotations softens the debris and it comes off easily.
The cutting edge of the skew is angled relative to the axis of the tool. (The axis runs the length of the tool.) The end of the cutting edge furthest from the handle is the long point, the other...
Bought a pin vice years ago. Had to wrap drill bit shank with blue tape, then clamp in the pin vice. Have to replace the tape rather often.
Richard Raffan has Youtube videos that address how to come up into the center, then swing out. You could cut tongue depressers to different lengths (if they truly have straight edges) as straight...
My first thought, with all that work, how can they sell the plane at such a low price.
I used to turn smaller bowls, 8-10" diameter, and have boxes of them in the attic, even black cherry and walnut, oak, maple, bradford pear. Despite being much more useable, they don't sell, unless...
I'm not sure how well softer woods like poplar might work over time with holdfasts. I would suggest getting some pieces of the wood you are considering, glue up two or three different thicknesses,...
Not to avoid answering, but "it depends." How strong is the wood? How heavy is the blank? Will the tailstock be tight against the bland? How clean is the edge of the mortise, and does the angle...
Keep in mind that screwl threads do not hold as well in end grain as in side grain. Bed bolts have machine thread that passes through the post and engages with a nut mortised into the bed rails.
My first suggestion would be to develop sound hand and body mechanics for controlling and moving the cutting edge of lathe tools. Dominant hand grips the handle right behind the ferrule, handle...
As soon as I finish a once-turned bowl, I note the weight in grams on the tenon, and place in a paper bag on the concrete floor (on grade). I weight every friday, and when the weight loss from the...