Search:

Type: Posts; User: Mark Rainey; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    636

    William, I agree with your opinion of the window...

    William, I agree with your opinion of the window to check chip level. The plastic scratches easily, and recently I thought I was being industrious and wiped it down with some solvent and it clouded...
  2. Mike, thank you for the pictures. The hand tool...

    Mike, thank you for the pictures. The hand tool methods of work is enjoyable to follow. I have a panel gauge and also use a pencil for the marker instead of a blade.
  3. Replies
    7
    Views
    636

    Oneida Mini Gorilla one year later

    Have been using the Oneida mini-gorilla for almost a year. I use mostly hand tools, but added Rikon band saw and Dewalt planer almost 2 years ago. Ran the Dewalt 735 into Rockler bag for a while,...
  4. Replies
    3
    Views
    431

    Good job Dave! The hardwood is eye catching

    Good job Dave! The hardwood is eye catching
  5. What a table Russell!

    What a table Russell!
  6. Replies
    10
    Views
    900

    Wow Ken, that disassembles beautifully.

    Wow Ken, that disassembles beautifully.
  7. Replies
    32
    Views
    2,232

    John, that is an impressive solar lumber drier. ...

    John, that is an impressive solar lumber drier. Plenty of good sticks in western NY.
  8. Good wisdom Charles, thank you

    Good wisdom Charles, thank you
  9. Do you use the nicker, do you trust it will cross...

    Do you use the nicker, do you trust it will cross cut grain without tear out? Or do you knife the line?
  10. Good tip Charles on not ripping to width until...

    Good tip Charles on not ripping to width until dados are done. Similar to what Warren recommends not ripping to width until ends are square - you don't worry about tear out on the far edge. And I...
  11. Replies
    2
    Views
    440

    Very useful - well done. I like walnut.

    Very useful - well done. I like walnut.
  12. That would be good if Steve was making a dado...

    That would be good if Steve was making a dado plane. That open house at Hearne looks interesting - I have not been to Hearne in many years. Have you been to the open house? If yes, was it...
  13. Replies
    15
    Views
    1,396

    Well done! That board will get put to good use!

    Well done! That board will get put to good use!
  14. Warren, Gordon's dado plane has this, if I...

    Warren, Gordon's dado plane has this, if I understand your statement correctly. What most confuses me is that with the resurgence of hand tools, almost no one is reproducing dado planes. Plow...
  15. Replies
    26
    Views
    1,251

    16 hours a week as hobby. At 60 I Work full...

    16 hours a week as hobby. At 60 I Work full time but trying to go part time so I can get a few more hours in shop,
  16. Derek, that is some impressive research on the...

    Derek, that is some impressive research on the dados produced by the Veritas combination plane and HNT Gordon dado plane! The dado width from the HNT 1/2 inch plane blade is only 3/1000ís wider! It...
  17. David, your challenging situation is not unusual....

    David, your challenging situation is not unusual. There are just a few neanderthals that are expert in dado plane use. Most use work arounds like knifing lines, sawing lines, etc. You should be...
  18. That is interesting Fred. I think he has a point.

    That is interesting Fred. I think he has a point.
  19. Replies
    19
    Views
    819

    William, that is a fine clock. I love tall case...

    William, that is a fine clock. I love tall case clocks.
  20. Replies
    15
    Views
    1,396

    Looking forward to the final cutting board Marlin.

    Looking forward to the final cutting board Marlin.
  21. Replies
    12
    Views
    994

    Well done Michael. The figure is the woods is...

    Well done Michael. The figure is the woods is beautiful.
  22. Replies
    37
    Views
    2,289

    Good contribution Herv.

    Good contribution Herv.
  23. Replies
    22
    Views
    1,520

    It is just as well Bill. Three people have...

    It is just as well Bill. Three people have recommended the router plane instead. You can really thickness the tenon to perfection with the tool if it does not come off the saw just right.
  24. Replies
    37
    Views
    2,289

    Bill, it is from "The Right to Useful...

    Bill, it is from "The Right to Useful Unemployment" 1978. Ivan Illich. I read it over 20 years ago, and looked at it again recently. I think he would admire woodworkers, especially neanderthals...
  25. Replies
    37
    Views
    2,289

    Yes Doug! 🙂

    Yes Doug! 🙂
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4