Search:

Type: Posts; User: Bill Bukovec; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    15
    Views
    400

    Did you look inside the switch box for a...

    Did you look inside the switch box for a schematic? I think that's where mine is. If you can isolate the wires for the centrifugal switch, use an ohm meter to verify the switch is closed when the...
  2. Replies
    24
    Views
    1,075

    Delta iron bed 1440. I like to slide the...

    Delta iron bed 1440. I like to slide the headstock close to the end of the ways for bowl turning. I bought it about 10 years ago. Hate the fact that the pulleys in the Reeves drive are cheap pot...
  3. Replies
    12
    Views
    445

    We bought flooring made by Mullican Flooring. We...

    We bought flooring made by Mullican Flooring. We were getting ready to sell our house, so I had someone install it. It looked beautiful.
  4. What town in Clark county, WI? I grew up in...

    What town in Clark county, WI? I grew up in Greenwood.
  5. Replies
    34
    Views
    1,185

    I hope she pulls through. We had been letting our...

    I hope she pulls through. We had been letting our hens free range evenings, but a hawk has been hanging around lately. A coworker lost a chicken to a hawk yesterday. They said the hawk was not...
  6. Replies
    27
    Views
    898

    I ordered bearings for my lathe last year. They...

    I ordered bearings for my lathe last year. They were only $20.00. They charged me another $20.00 for shipping. I had placed the order over the phone, so I didn't ask for a total, including shipping.
  7. What do you want to make with it?

    What do you want to make with it?
  8. Replies
    8
    Views
    1,086

    I think it makes perfect sense. Let us know how...

    I think it makes perfect sense. Let us know how it works out. I am thinking of harvesting pine trees from our property to build a timber frame carport, replace the roof on an out building. We also...
  9. Replies
    13
    Views
    847

    When applying the tape, leave it attached to the...

    When applying the tape, leave it attached to the roll. Then peel the backing back. Cut the tape, leaving the backing attached to the roll. Then trim the backing so it's sticks past the end of the...
  10. Replies
    3
    Views
    533

    Vega model # 24 wood lathe

    I saw a Craig's list and for an "older Vega model # 24 wood lathe". Is anyone familiar with this model, and is it worth $550? Seller is located near Gate City, VA.
  11. Replies
    11
    Views
    875

    Well done!

    Well done!
  12. I would buy a new lathe if you have the money....

    I would buy a new lathe if you have the money. There are always a few unseen problems that crop up that get to be a pain in the neck. I converted my Delta iron bed 1440 from Reeves drive to step...
  13. Replies
    5
    Views
    680

    Our kindergarten teacher would do our ...

    Our kindergarten teacher would do our silhouettes. Too bad I didn't still have it. I could have turned myself!
  14. Replies
    16
    Views
    1,223

    I'm amazed that I got so old in such a short...

    I'm amazed that I got so old in such a short amount of time.
  15. Replies
    8
    Views
    1,101

    Here is the jig I made. The blank sits at a 13...

    Here is the jig I made. The blank sits at a 13 degree angle (more or less). I start with a blank 3" x 3" x 24" long. I number each side of the blank, 1 thru 4. The first cut is made with the left...
  16. Replies
    21
    Views
    1,345

    Norwood sawmills ha a board feet, Doyle scale...

    Norwood sawmills ha a board feet, Doyle scale calculator. It also calculated the weight of lumber or a log.
  17. Try giving the motor a good smack. If it starts...

    Try giving the motor a good smack. If it starts after that, you may have a bad start switch inside the motor. Where do you live? Someone may be close enough to help.
  18. Replies
    6
    Views
    583

    Yes, you could make it easily with a 3D printer....

    Yes, you could make it easily with a 3D printer. I redesigned and printed parts for the start switch on my Unisaw. I even made a dust port for the saw as well. You need to start with a diagram with...
  19. Have you called Grizzly?

    Have you called Grizzly?
  20. Replies
    133
    Views
    17,871

    Sticky: Count me in!

    Count me in!
  21. Replies
    23
    Views
    1,353

    Thanks for the posts. Look there may be a steady...

    Thanks for the posts. Look there may be a steady in my future!
  22. Replies
    4
    Views
    457

    Very nice! What did you use to hollow it out?

    Very nice! What did you use to hollow it out?
  23. Richard is correct. The pulleys are extremely...

    Richard is correct. The pulleys are extremely fragile. To make matters worse, Delta no longer sells the parts. Seriously Delta, did you think those lousy pulleys would go unnoticed?
  24. Replies
    81
    Views
    6,985

    A job well planned, is a job half done.

    A job well planned, is a job half done.
  25. Thanks Bill, that makes sense. My next step would...

    Thanks Bill, that makes sense. My next step would be to wire a light switch across terminals 2 & 3. Put this switch in the open position. Name this one Start.

    Next, wire a switch across terminals...
Results 1 to 25 of 462
Page 1 of 19 1 2 3 4