Search:

Type: Posts; User: Phillip Mitchell; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.28 seconds.

  1. Replies
    19
    Views
    664

    I've always disposed of oily rags by putting them...

    I've always disposed of oily rags by putting them straight into a lidded 5 gallon container that is at least half filled with water, completely submerging them in water and closing the lid. I think...
  2. Replies
    13
    Views
    624

    I drove 10 hrs (each way) for my 66 that is...

    I drove 10 hrs (each way) for my 66 that is similar age to yours. 3 HP baldor, 52 fence, couple of Forrest blades, aftermarket miter gauge. Only ding against it is some surface rust inside the base,...
  3. Replies
    28
    Views
    3,140

    Thanks Jim. I just sent him an email.

    Thanks Jim. I just sent him an email.
  4. Replies
    28
    Views
    3,140

    Bringing this thread back from the dead a...

    Bringing this thread back from the dead a bit...does anyone know the actual height (off the floor) of the MM 24? I’ve googled for the last 20 minutes and am still coming up empty handed with overall...
  5. Replies
    24
    Views
    1,349

    You might wander over to owwm.org and do some...

    You might wander over to owwm.org and do some searches. Lots of PM 1150 / 1200 discussion and rebuilds there.
  6. Replies
    19
    Views
    924

    Do you currently have a bandsaw or have any...

    Do you currently have a bandsaw or have any experience with using one? What are your expectations? How much re-saw capacity do you really want / need? Do you have a jointer or planer or have the...
  7. Thanks for the reply, Jeff! Definitely helps to...

    Thanks for the reply, Jeff! Definitely helps to hear some first hand feedback. That's about what I expected to hear, but wanted to know if there were any issues with this particular model.

    I'd...
  8. I'm also on the same path. I started with the...

    I'm also on the same path. I started with the 12" Oliver 166 jointer and have been on the hunt for an old arn planer and mortiser for the last year or two. Keeps things interesting looking for the...
  9. SCM S50 planer - anybody have experience

    Does anybody know any specs on the SCM S50 planer? I've seen plenty of the S52 and S520 models around...visually, the S50 appears to have been concurrent with the S52/63, but seems odd to have a...
  10. Replies
    59
    Views
    3,702

    Buy used is a much better value and the older...

    Buy used is a much better value and the older machines were built better than most of what you can buy new these days.
  11. Replies
    59
    Views
    3,702

    It all depends on what you build, the lumber you...

    It all depends on what you build, the lumber you tend to work with, and how much it bothers you to rip down lumber just to mill it. Everybody will have different answers to the above criteria, but in...
  12. Replies
    59
    Views
    3,702

    This is the truth

    This is the truth
  13. Replies
    19
    Views
    868

    I have a 12" Oliver 166 and would never want to...

    I have a 12" Oliver 166 and would never want to move it around and not even because it weighs 2000 lbs...more because I have it dialed in where it currently sits and there is no twist in the base. ...
  14. Replies
    23
    Views
    1,206

    Bigger is always better with jointers if you have...

    Bigger is always better with jointers if you have the space and budget. That is all.
  15. Replies
    11
    Views
    678

    I've this happen plenty of times with impact...

    I've this happen plenty of times with impact drivers of different makes. If you tap the end of the stuck bit abruptly on a hard surface, many times the shock of the impact can loosen the driver bit...
  16. Yep, that's what I was going to say in my...

    Yep, that's what I was going to say in my previous post was that if I did strictly or even mostly job site finish work (cabinet installs, finish carpentry, etc) and didn't have a shop with a nice...
  17. I've got tons of Black Locust that would fit that...

    I've got tons of Black Locust that would fit that bill. What is the intended use? Straight grain? S4S? Hell, if don't ever make it up to my neck of the woods and you pay shipping and handling...
  18. I own the Makita (cordless) track saw, have used...

    I own the Makita (cordless) track saw, have used both a TS55 and TS75 as well as the Mafell MT55 track saw. For an appropriately outfitted Mafell track saw setup comparable to my Makita setup...
  19. Replies
    1,328
    Views
    99,588

    Patrick, I know where you’re at and how you...

    Patrick,

    I know where you’re at and how you feel. I’ve been in a similar situation but I’m 32, have young kids and a wife, and live in a somewhat rural area, so slightly different circumstances...
  20. I'm building a custom sized maple entry door...

    I'm building a custom sized maple entry door right now and was really struggling to find the proper door bottom / sweep and jamb weather stripping options and came across this thread on a search. ...
  21. Replies
    24
    Views
    1,342

    Don't worry about it! I appreciate your testing...

    Don't worry about it! I appreciate your testing and I understand and can sympathize with your methods and musings.

    Yes, a framing square is intended for framing, but good lord, if you can get it...
  22. Replies
    14
    Views
    803

    Why do some folks think that JET machines are...

    Why do some folks think that JET machines are worth so much? I've used a lot of JET tools over the years (never owned any) and never thought they were anything special or really any different than...
  23. Replies
    24
    Views
    1,342

    I think you got lucky and happened to get a good...

    I think you got lucky and happened to get a good one. I've worked as a timber frame carpenter and know my way around a framing square and have had several different squares in my hands. It's good...
  24. I'll second Bear Creek Lumber. I've seen very...

    I'll second Bear Creek Lumber. I've seen very nice CVG Doug Fir and CVG Alaskan Yellow Cedar come from them on multiple occasions. Shipping it across the country is not cheap, but if you can't find...
  25. Thanks for all the knowledge and replies. All of...

    Thanks for all the knowledge and replies. All of this is very helpful.
Results 1 to 25 of 362
Page 1 of 15 1 2 3 4