Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.31 seconds.

  1. Replies
    6
    Views
    286

    I priced a book matched elm burl veneer for my...

    I priced a book matched elm burl veneer for my 5" diameter table and repaired what I have. Over $400 for the wood. It would be cheaper to buy an antique in good condition and refinish it as...
  2. cleaning segmented infeed rollers on a planer

    My Powermatic planer has a segmented infeed roller. All I can find online is how to clean a rubber covered roller. It has some pitch and what not embedded into the teeth. I assume a wire brush and...
  3. Replies
    3
    Views
    162

    You do not set the blades at 90. You set them so...

    You do not set the blades at 90. You set them so the knife edge is as high as it can be. You need to level the tables to the blade height before removing them. Sounds to me like your blades are...
  4. Replies
    25
    Views
    546

    Watch out for free upgrades. We had to go to 4g...

    Watch out for free upgrades. We had to go to 4g and Verizon offered to give us free phones that would work. They were free because we were long time customers.
    Problem was if you took the "free"...
  5. Replies
    3
    Views
    147

    I should have said weathertech is cut to fit. ...

    I should have said weathertech is cut to fit. Husky says they have made to fit.
    Bill D
  6. I got the dovetails cleaned up without table...

    I got the dovetails cleaned up without table removal. In was able to pull the gibs then get some tools in to clean them out. The outfeed table was the worst I kept getting fine grit on a pipe...
  7. Replies
    3
    Views
    147

    Floor mats for my Ford Ranger, 2000

    I need to get some new floor mats for my 2000 ford ranger. I want heavy rubber no carpet or leather. No one seems to make ones that custom fit. If I have to cut to fit anyway I do not see the...
  8. Replies
    5
    Views
    301

    Do not overclean the coils. Coils transfer more...

    Do not overclean the coils. Coils transfer more heat if they are slightly rough. factory new clean and polished get better as a light dust film forms and causes turbrulance in the air flow.
    Bill D
  9. Replies
    29
    Views
    3,594

    I will jump in here without having read all the...

    I will jump in here without having read all the previous posts. I think for most people you do not really care too much about the actual flow rates and pressures. You are simply trying to get max...
  10. Replies
    13
    Views
    765

    Politically correct term for Nipple Extractor....

    Politically correct term for Nipple Extractor.
    Bill D
  11. Replies
    16
    Views
    614

    I asked and Harbor Freight where everything is...

    I asked and Harbor Freight where everything is made outside the only Inch country in the world has no metric measuring tapes. Most of their metal measuring scales have metric and English ,but no...
  12. Replies
    13
    Views
    765

    The advantage of the square kind is the taper is...

    The advantage of the square kind is the taper is the same angle as NPT threads. so less likey to deform compared to easy out angle. The cam type has no taper since then inside of pipe is not...
  13. Every time I read about someone cleaning parts,...

    Every time I read about someone cleaning parts, in the house, in gasoline they are always motorcycle parts. I do not think motor cycle parts are more likely to spontaneously combust. I bet the...
  14. Replies
    9
    Views
    598

    You could run the cutterhead with a fixed speed...

    You could run the cutterhead with a fixed speed motor and drive the feed with a vfd controlled motor.
    Bill D
  15. Replies
    2,179
    Views
    313,989

    Sticky: Home Depot is now selling spray painted cactus. ...

    Home Depot is now selling spray painted cactus. I have no idea if the green cactus under the paint will live or not. I know in Southern California companies will come spray paint your gravel...
  16. Replies
    13
    Views
    765

    "Nipple extractor" that is what they are...

    "Nipple extractor" that is what they are designed for. Copper may be a problem as it will tend to creep and flow under load. For such a short section I would think the kind with a moving cam would...
  17. Mix up a non newtonian fluid, pour it in push it...

    Mix up a non newtonian fluid, pour it in push it into joint, cut bck as needed(work very fast). Then let it reliquidfy and pour it out and measure the liquid. Corn starch and water is a classic...
  18. Doubtful since it is summer here in California....

    Doubtful since it is summer here in California.
    Bill D
  19. Replies
    2,179
    Views
    313,989

    Sticky: Interesting to see the last picture of the engine...

    Interesting to see the last picture of the engine to see the small size of the generator it powers. Or is that the starter motor?
    Bill D.
  20. Thread: bee trap

    by Bill Dufour
    Replies
    10
    Views
    661

    Learned something new. thanks. Bill D

    Learned something new. thanks.
    Bill D
  21. Replies
    9
    Views
    598

    Never heard of the maker. I am sure no parts...

    Never heard of the maker. I am sure no parts available.
    Bill D.
    ...
  22. Replies
    9
    Views
    598

    Seems a fair price if the motor is included. I...

    Seems a fair price if the motor is included. I see used plastic lunch box planers for similar prices. Price a set of three iron gears for the feeder. It is a simple machine but few were sold...
  23. Wind load is a big impact on such a large roof. ...

    Wind load is a big impact on such a large roof. Any seismic concerns?
    Bill D
  24. Thread: bee trap

    by Bill Dufour
    Replies
    10
    Views
    661

    What makes that a trap and not just a empty hive...

    What makes that a trap and not just a empty hive waiting for new tenants?
    Bill D
  25. No pictures make it hard to know much at all. ...

    No pictures make it hard to know much at all. $6.00 is too rich for the OP. Any one able to post some pictures he can choose from? I posted a link to the same model # but someone said it was...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4