Search:

Type: Posts; User: Ronald Blue; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    4
    Views
    110

    I use adblock plus and it seems to do a good job...

    I use adblock plus and it seems to do a good job for a free program. I occasionally try to go to a website that won't let me unless I turn my adblocker off. It just requires me to allow that website...
  2. Replies
    13
    Views
    732

    I always hold the dipstick up and look across it...

    I always hold the dipstick up and look across it so I can see the layer of oil on it above the metal when it's difficult to see. Dulling the shine of the metal will help though.
  3. Replies
    10
    Views
    643

    I found the same thing. On the Oatey website they...

    I found the same thing. On the Oatey website they say their yellow PFTE tape is approved by code for use on natural gas lines and the yellow color is to make it easily identified.
  4. It comes up in a google search as a half link....

    It comes up in a google search as a half link. Change the 005 to 004 and it's a master link. If you have any farm stores (Tractor Supply or similar) or farm equipment dealers in your area they should...
  5. Unlikely. Everything uses larger chain than that,...

    Unlikely. Everything uses larger chain than that, is usually an o-ring type, and is endless.
  6. Replies
    13
    Views
    732

    We found Royal Purple gear lube was pure crap. It...

    We found Royal Purple gear lube was pure crap. It didn't stand up to the temperatures in a three pump industrial hydraulic drive. What a mess it left. It was a scaley mess on everything. Like when a...
  7. Replies
    38
    Views
    1,881

    Just get a hard side case that you can put a lock...

    Just get a hard side case that you can put a lock on. That will be more than sufficient.
  8. Replies
    38
    Views
    1,881

    Try being in Illinois. It's probably a horse race...

    Try being in Illinois. It's probably a horse race to see who can pass the most anti-enthusiast laws. I will end it with that.
  9. Replies
    13
    Views
    1,032

    I'm going to go against the grain here. No if the...

    I'm going to go against the grain here. No if the bolts were properly tightened the first time they don't need retorqued. You should as was suggested look into replacing the blades.
  10. I think you are already on the Shopsmith forum...

    I think you are already on the Shopsmith forum but there is also a FB Shopsmith owners group which is not connected. I know there are members there that aren't on the forum. If you do FB it might be...
  11. Replies
    8
    Views
    979

    I would get it and get it up in shape and then...

    I would get it and get it up in shape and then decide. There are not a lot of major differences but a foot brake would be one. Also two dust collection ports.
  12. Replies
    2
    Views
    414

    Not sure if this is where you found it. Not cheap...

    Not sure if this is where you found it. Not cheap but it does seem to be available. If it's the correct handle.
    https://www.ereplacementparts.com/head-wheel-p-1107219.html
  13. It's 70 degrees at this moment here in West...

    It's 70 degrees at this moment here in West central Illinois. There was a tornado warning about 40 mile west of me that's now expired. I was working outside in my Tee-shirt today.
  14. Replies
    9
    Views
    570

    I googled 8 mm router bits and came up with...

    I googled 8 mm router bits and came up with several matches. Whether they are what you are seeking I don't know. Amana has one but it's also an 8mm shank.
  15. Replies
    100
    Views
    7,962

    Back in the 80's when employee involvement and...

    Back in the 80's when employee involvement and quality circles were a thing that was a catch phrase.
  16. Replies
    260
    Views
    27,876

    If you can steer me to that information I would...

    If you can steer me to that information I would appreciate it. My searches have came up empty. In fact everything I have found indicates there is no longer a Bosch Reaxx table saw.
  17. Thread: Dash Cams

    by Ronald Blue
    Replies
    7
    Views
    1,067

    My employer went "full in" with DriveCam in 2014...

    My employer went "full in" with DriveCam in 2014 I believe it was. Big brother is watching sort of thing. Looked forward and also in the cab. Active anytime vehicle was on but took an "event" to...
  18. Replies
    260
    Views
    27,876

    If there is even an ounce of sincerity in these...

    If there is even an ounce of sincerity in these used oats they will allow the Bosch system to be in play as well if this gets forced upon the consumer.
  19. Replies
    18
    Views
    2,198

    There will always be those that know how you...

    There will always be those that know how you should spend your time and money better than you. Like Earl said don't sweat it. I upgraded my planer and jointer both to insert heads because even though...
  20. Replies
    9
    Views
    1,305

    Looks like the way to go then. I believe there...

    Looks like the way to go then. I believe there are two bolts in each bearing block. It seems like I removed a sheet metal cover on my 6" Jet for access to possibly the bolts on the opposite end from...
  21. Replies
    9
    Views
    1,305

    Andrew it occurred to me that you have to remove...

    Andrew it occurred to me that you have to remove the pulley regardless of which insert head you go with. The bearing block is mounted behind the pulley. You will need to remove both bearing blocks...
  22. Replies
    8
    Views
    1,104

    Get a 90 street el and go to the farm store and...

    Get a 90 street el and go to the farm store and get a hydraulic hose with the same size male pipe threads. Either grab a pipe coupler or get a ball valve with female threads to screw on the end of...
  23. Replies
    9
    Views
    1,305

    I put the Byrd Shelix on my Delta DJ-20 last...

    I put the Byrd Shelix on my Delta DJ-20 last summer and haven't looked back. I have no experience with the Grizzly V style head but in this instance go with the Shelix IMHO. You can source bearings...
  24. Replies
    260
    Views
    27,876

    In the comment section of the article I linked...

    In the comment section of the article I linked someone claims that there are additional patents protecting the Sawstop technology past 2030. I personally am highly skeptical of this. So Stephen Gass...
  25. You never mentioned if you tried waxing as John...

    You never mentioned if you tried waxing as John said but my Powermatic PM 15 was getting a little temperamental with an occasional board stalling and I waxed the table and it was like a new machine....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4