Search:

Type: Posts; User: Jim Becker; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.34 seconds.

  1. Replies
    2
    Views
    138

    Nothing like a "simple" last operation for the...

    Nothing like a "simple" last operation for the end of a major project. LOL :D

    I agree with making the stairway look like it belongs in a timber frame structure, either by using wood in the way I...
  2. Replies
    8
    Views
    417

    You just need to make a custom sled that can...

    You just need to make a custom sled that can attach to your wagon so that the workpiece is held steady and vertical through the steep angled cut. Be sure that the offcut is also supported with some...
  3. Replies
    22
    Views
    1,285

    Those doors are going to look SO good when your...

    Those doors are going to look SO good when your project is completed. Really transformational!
  4. Replies
    6
    Views
    638

    So I can officially say that I've scraped...

    So I can officially say that I've scraped together enough of the scrap to create the whole Scrap Vanity and no more scrap scraping is required. It's built. I may or may not add some kind of shadow...
  5. EM8000cv is the top coat. It's even more durable...

    EM8000cv is the top coat. It's even more durable than the EM6000. The cross linker primarily provides increased chemical resistance to the Target Coatings finishes you add it to for that specific...
  6. Replies
    17
    Views
    1,034

    We finally just got a break from the excessive...

    We finally just got a break from the excessive humidity and that should hold through the week. There's also an upper level low that will be sitting above us for a few days, so there's hope for some...
  7. Replies
    13
    Views
    548

    Looks like it was wired with a common 3-wire...

    Looks like it was wired with a common 3-wire dryer plug to match whatever receptacle was in your previous shop. Base on your photos, it's actually correct. Here's why...

    Green is ground normally,...
  8. Replies
    32
    Views
    1,313

    While I prefer a wider arrangement as comes with...

    While I prefer a wider arrangement as comes with a J/P combo, I'll echo what Glenn just mentioned...pick something that's available as there really isn't anything innovative about most 8" jointers....
  9. Replies
    13
    Views
    31,262

    Sticky: Change your bookmark for the site to "that page"...

    Change your bookmark for the site to "that page" after you do the click on the logo, etc.
  10. Replies
    17
    Views
    1,034

    Send some here, Alan. I'd be very happy to take a...

    Send some here, Alan. I'd be very happy to take a third of that from you at the moment...it's very "crispy" walking outside right now...
  11. Replies
    1
    Views
    164

    If I'm not mistaken, the rails on the PCS out in...

    If I'm not mistaken, the rails on the PCS out in my temporary shop uses a 2x3 format. I measured it with the intention of buying some steel to make longer rails for it as they were cut down "a lot"...
  12. Replies
    6
    Views
    638

    Today was drawer day...which started out with a...

    Today was drawer day...which started out with a little "shopping" in the shed

    484347

    After cutting two pieces of leftover QSWO 12.5mm plywood to manageable size with the tracksaw and taking...
  13. Replies
    20
    Views
    2,422

    Aaron, there is an extensive plan for sound...

    Aaron, there is an extensive plan for sound abatement in the new shop building to be implemented and yes, some of that will be focused on the G700 location in addition to general sound consideration...
  14. That's interesting considering it's sold as paint...

    That's interesting considering it's sold as paint thinner and many of us also use it for cleaning because it doesn't leave a film behind like "mineral spirits". Or is the naptha sold in the big box...
  15. Replies
    15
    Views
    661

    The only two options I would entertain for this...

    The only two options I would entertain for this would be to either rewire the circuit properly for four wire 120/240v operation per code or replace the VFD with another 120v VFD.
  16. Replies
    10
    Views
    517

    Clear the existing sawmillcreek.org cookie(s),...

    Clear the existing sawmillcreek.org cookie(s), close the browser completely (and consider rebooting the machine and then start the browser followed by logging in with the box checked to remember you....
  17. Replies
    8
    Views
    887

    Yes, initial cost is high, but after a few years,...

    Yes, initial cost is high, but after a few years, things will balance out a bit more and the quality of the veggies takes the rest of the pain away!
  18. That extra mass isn't hurting you in the "runs...

    That extra mass isn't hurting you in the "runs smoother" department, for sure. 'Glad it's working out!
  19. Replies
    8
    Views
    887

    Construction lumber, in general, is coming down...

    Construction lumber, in general, is coming down in price across the board, but some of the anomalies we might see out there in the home centers and lumber yards could certainly be from what they paid...
  20. That may not be true for the portables that the...

    That may not be true for the portables that the OP is considering, at least yet. Cordless tools have very much gone that route, however.

    ----

    OP, that brings up something to consider. There are...
  21. Replies
    2
    Views
    339

    No experience, although I actually touched one...

    No experience, although I actually touched one years ago. They were a decent dedicated resaw machine back in the day.
  22. Replies
    20
    Views
    2,422

    Bryan, no, I'm not up for doing my own spray foam...

    Bryan, no, I'm not up for doing my own spray foam other than corner sealing. I'll get some more current quotes, however, once I'm closer to build. Getting response has been difficult and I may have...
  23. Replies
    41
    Views
    2,325

    Steve, I don't disagree with TWW's logic on...

    Steve, I don't disagree with TWW's logic on that...a whole bunch of cross cutting really is at 90 in my experience, so a fixed fixture, as it were, can be ideal for a lot of that work. I don't...
  24. Replies
    23
    Views
    1,173

    I've been thinking about the same thing as I...

    I've been thinking about the same thing as I visited this thread each day to see what folks have been saying. I suspect that a digital scale would be a lot more reliable than the optical sensors...
  25. Thread: MillRight?

    by Jim Becker
    Replies
    26
    Views
    1,890

    As decent and capable that Mach4 is, Acorn is...

    As decent and capable that Mach4 is, Acorn is very much next level, IMHO. It's nice that the option is there to folks to do an upgrade like that.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4