Search:

Type: Posts; User: derek labian; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Right. I didn't see any need for an input...

    Right. I didn't see any need for an input disconnect because the unit is effectively idle when the output is turned off. Once you turn on the output it engages. Its like any other appliance, ready to...
  2. “ just before the single phase input / line side...

    “ just before the single phase input / line side so I don’t have to use the circuit breaker as an on/off switch”

    I have a 10hp PP unit and while it doesnt come with a “on off switch” its designed...
  3. I've been away from this project for a while,...

    I've been away from this project for a while, resorting to other methods for straightening wood. Here's what I've observed about my jointer:


    1. With the jointer set to a 0" cut, both in-feed and...
  4. Replies
    51
    Views
    6,520

    Amazing work Joe! I love to see OWWM restored to...

    Amazing work Joe! I love to see OWWM restored to original glory. In your case, perhaps, better than original.
  5. Replies
    3
    Views
    619

    Thank you for the feedback. I already have the...

    Thank you for the feedback. I already have the bits and it just so happens that Fisch 3/8 10" is the brad point I was considering against a modern Wood Owl Auger or a steel Craftsman Auger (circa...
  6. Replies
    3
    Views
    619

    Auger vs Brad Point Long Bit

    I'm looking to drill a deep and narrow hole, approximately 10 inches deep with a diameter of 3/8". I'm unsure which type of drill bit would be the best option for a straight and accurate hole. I've...
  7. Replies
    52
    Views
    6,227

    I use my No 4 smoothing plane more than anything...

    I use my No 4 smoothing plane more than anything else, but the most valuable (hardest to replace) would be No 51.
  8. Replies
    13
    Views
    1,659

    You would do better to challenge ChatGPT if it...

    You would do better to challenge ChatGPT if it gives you incorrect information or something you think may be incorrect:



    Followed up by your complaint:




    You said you can't know the...
  9. Replies
    21
    Views
    3,226

    What a wonderful view. I hope you have some great...

    What a wonderful view. I hope you have some great vista's out of that window in the new gara-shop :)
  10. Replies
    16
    Views
    2,515

    Jeff / Erik, I think you guys are just talking...

    Jeff / Erik,

    I think you guys are just talking past each other. Erik has no dog in this fight; he's just trying to give a different perspective.

    It's a standard expectation that as you double,...
  11. Replies
    16
    Views
    2,515

    Sounds about right regarding support. Can't help...

    Sounds about right regarding support. Can't help with the segmented roller. I think a lot of it comes down to internal disorganization and technical issues. I'm still waiting for a factory damaged...
  12. Replies
    1
    Views
    938

    Festool with Sawstop AIM

    I saw that Festool's parent is making use of the Sawstop acquisition by integrating cartridges into the table saw. I know there were a few conversations about what if anything they would do. No we...
  13. Replies
    16
    Views
    1,963

    I always use Blum but thats because its what I've...

    I always use Blum but thats because its what I've always used. See this thread: https://sawmillcreek.org/showthread.php?234896-Blum-Undermount-Drawer-Slides-and-Inset-Drawers

    You could also just...
  14. Replies
    31
    Views
    4,151

    I have 4 sets of Forstner bits, and the Fisch are...

    I have 4 sets of Forstner bits, and the Fisch are by far the best I've used. They cut hard maple like butter. I purchased after seeing and meeting the Fisch guys at a show. I'm sure the Freud are...
  15. Hi Mike, Are you trying to avoid using a...

    Hi Mike,

    Are you trying to avoid using a square to get it perfectly 90 by using the stop or are you prevented from getting it to 90 by the stop? Seems like this will certainly be adjustable,...
  16. Hi Ben, I had a 4100 a few years ago and I...

    Hi Ben,

    I had a 4100 a few years ago and I don't recall any transfer issues to workpieces, but the top did get easily scratched. I assume that if the workpiece that created the scratches also got...
  17. Replies
    23
    Views
    2,776

    I guess i had the opposite experience ironically,...

    I guess i had the opposite experience ironically, although it seems likely my experience was an anomaly. I purchased a California Air Tools "industrial" compressor for around $1500. The tank is not...
  18. There is an update. The bolt is off after a mere...

    There is an update. The bolt is off after a mere seven months :) After getting suggestions to try a few other things, SCM suggested a strap wrench. That worked well but ultimately slipped. I combined...
  19. Replies
    15
    Views
    1,321

    I paid ~$1300, so there is some value. I heard...

    I paid ~$1300, so there is some value. I heard the interest in them fell off with options like the domino (as others have noted), however, if you want to make a larger mortise for an integral tennon,...
  20. Replies
    58
    Views
    12,306

    How exciting, for timber framing, that's like the...

    How exciting, for timber framing, that's like the Superbowl.



    Looking forward to seeing it.
  21. Replies
    36
    Views
    4,601

    I am not worried about fresh air in the dust box...

    I am not worried about fresh air in the dust box if the material isn't building up. My problem with most (square) dust boxes is build-up in the corners of the box. I recently switched to the Harvey...
  22. Depending on who you are buying from, they may be...

    Depending on who you are buying from, they may be a tax-exempt dealer. For example, if a dealer sells from a state that does not collect sales tax to a state that has exemptions for that category...
  23. Replies
    905
    Views
    168,902

    that nesting, with the g700, worked out really...

    that nesting, with the g700, worked out really well.
  24. Very sad, everything is OK until it isn't. I...

    Very sad, everything is OK until it isn't. I can't watch YouTube video's with close to blade operations anymore..
  25. It seems almost certain they tried to keep the...

    It seems almost certain they tried to keep the company afloat and were unable leading to continue; a catastrophic failure. It could be a bond that came due, lack of a loan or financing, etc. I doubt...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4