Search:

Type: Posts; User: John Lanciani; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.27 seconds.

  1. Replies
    3
    Views
    679

    All sold, thank you all for your interest.

    All sold, thank you all for your interest.
  2. Replies
    3
    Views
    679

    Any interest on the remaining two if i cover the...

    Any interest on the remaining two if i cover the shipping?
  3. Yes. It will be something like 1100 cfm at 0"wc...

    Yes. It will be something like 1100 cfm at 0"wc and 0 cfm at 15"wc.
  4. Replies
    3
    Views
    679

    1 1/4" bore shaper tooling

    Freud RP1000 raised panel cutter wth RP-A & RP-E knives and back cutter. $100 obo
    SOLD - Amana 61470 125mm dia x 30mm height rabbet cutter w/ full boxes of new inserts $80 obo
    Amana 61411 125mm x...
  5. SOLD, thanks for looking.

    SOLD, thanks for looking.
  6. Any interest at $2200?

    Any interest at $2200?
  7. Replies
    29
    Views
    2,750

    Lots of ways to skin the cat, i typically take...

    Lots of ways to skin the cat, i typically take the first few shavings from planing and put themin the spot where i rest my planes (upright). This way the plane is ready to grab naturally and i dont...
  8. Replies
    22
    Views
    2,230

    See my post from a while back here;...

    See my post from a while back here; https://sawmillcreek.org/showthread.php?212757-Dust-collector-test-equipment-an-offer&highlight=

    LMK if you're intrrested.
  9. Rojek PK250A Sliding table saw (Central MA)

    59" slider, 36" rip capacity, takes 10" or 12" blades and also stack dados up to 8" 3/4" w/ 5/8" bore. Scoring blade is belt driven off main motor. 240 volt single phase 3.6hp motor. Includes two...
  10. If you have a Byrd head why would you even be...

    If you have a Byrd head why would you even be considering generic inserts from Grizzly, especially when they are more expensive than OE?

    Sure doesn't seem very confusing to me.
  11. Replies
    32
    Views
    2,651

    I've been using a DD 750 since not long after...

    I've been using a DD 750 since not long after they came out; every single time it has produced unsatisfactory results has been traced back to operator error...
  12. Replies
    16
    Views
    1,052

    Always making lemonade, you continually inspire...

    Always making lemonade, you continually inspire me John.
  13. Replies
    16
    Views
    1,052

    To add to Brian's answer, ring shake can also be...

    To add to Brian's answer, ring shake can also be caused by felling a tree onto a hard surface or across another tree trunk. The stress from the impact can separate the growth rings as shown in your...
  14. Try Bingham Lumber in Brookline NH; 603-673-4549

    Try Bingham Lumber in Brookline NH; 603-673-4549
  15. Replies
    102
    Views
    8,985

    The ultimate irony; using a forum on the internet...

    The ultimate irony; using a forum on the internet to wonder aloud about people using tools and materials that arent 100 years old...
  16. The Woodery is gone. Try Northland Forest...

    The Woodery is gone. Try Northland Forest Products in Kingston NH.


    Also, Highland Hardwoods in Brentwood NH is currently listing soft maple as low as $3.05 b/f and hard maple starting at $3.80...
  17. Replies
    10
    Views
    1,746

    Ligntning travels 1,000's of feet from clouds to...

    Ligntning travels 1,000's of feet from clouds to ground, there is absolutely nothing that you can do to mitigate a direct or near strike. Turning off breakers, adding surge protection, etc. are just...
  18. Replies
    36
    Views
    3,863

    If that Delta Crescent jointer is as complete and...

    If that Delta Crescent jointer is as complete and original as it looks I'd give $1200 for it in a heartbeat. The cast iron base alone weighs as much as most new 6" jointers.
  19. Replies
    13
    Views
    910

    Only if its a backwards rotation (CCW) bit. Look...

    Only if its a backwards rotation (CCW) bit. Look closer, thats an upspiral.
  20. Replies
    11
    Views
    743

    Not always that easy. Some of the bearings used...

    Not always that easy. Some of the bearings used by W-T were made of unobtanium. (Not available any more)
  21. Replies
    57
    Views
    8,505

    You added a zero to the price of the Byrd...

    You added a zero to the price of the Byrd inserts; they are priced per 10, not $41.50 each. Big differrnce.
  22. Replies
    18
    Views
    2,721

    22' 2x6 is nothing more than a rafter tie, not...

    22' 2x6 is nothing more than a rafter tie, not rated for load bearing at all. There isnt a load chart in the world that rates that for 50 lb/sf.
  23. Replies
    5
    Views
    888

    I like using pex crimp rings (the copper ones),...

    I like using pex crimp rings (the copper ones), they are about 3 for a buck for 1/2" or 3/4", 2 for $1 if you need 1".
  24. Replies
    33
    Views
    8,048

    No particle meter, but i do have a sound meter.

    No particle meter, but i do have a sound meter.
  25. Any company that sold a 3g device in the last 5...

    Any company that sold a 3g device in the last 5 years has committed outright fraud on their customers. As has been said this has been expected for a long time. The only reason 3g even still exists is...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4