Search:

Type: Posts; User: Charles Grauer; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    431

    It looks like 24 tooth, that I would guess would...

    It looks like 24 tooth, that I would guess would make it a rip saw. I would clean it up and see if you see any markings. Baking soda soak and a brass or fiber brush.
  2. Good for you.

    Good for you.
  3. You are not missing anything, the jig dimensions...

    You are not missing anything, the jig dimensions are incorrect. Just make it bigger so you can rotate the rollers. The no on putting a wedge underneath to raise it for the taper works tho. If...
  4. Replies
    7
    Views
    667

    I called and talked them him about them, if I...

    I called and talked them him about them, if I could sharpen carbine on the CBN and his answer was NO. I sharpen carbide a lot on my worksharp so I didn’t buy any.
  5. Replies
    16
    Views
    883

    Another way to cut the mortises on the side...

    Another way to cut the mortises on the side pieces top and bottom, is cut a dado to fit the thickness of the slats and then use spacers between the slats. Effectively giving you a mortise.
  6. Replies
    4
    Views
    341

    Thank you. Nice explanation and the pictures...

    Thank you. Nice explanation and the pictures are wonderful. Thanks! I just need to get it out and see if I have all those accessories. Charles
  7. Replies
    4
    Views
    341

    Could you explain how to split off the lid using...

    Could you explain how to split off the lid using a Stanley. I have a 45 that was my wifeís great grandfatherís. Just never taken, figured out how to use it, the time to figure it out. Do you...
  8. I would try running the center of the blade on...

    I would try running the center of the blade on the center of the wheel, crown, so the blade is tensioned it evenly. Running the gullet on the center puts more tension on the front of the blade and...
  9. Replies
    6
    Views
    733

    Nope, someone beat us both Ricc.

    Nope, someone beat us both Ricc.
  10. Replies
    6
    Views
    733

    Iíll take them both. jcgrauer@gmail.com iíll...

    Iíll take them both. jcgrauer@gmail.com

    iíll send you a PM if I can figure that out
  11. Replies
    7
    Views
    1,505

    What do you think of the pocket hole jig? Have...

    What do you think of the pocket hole jig? Have the plans, contemplating construction. Did you order the copper tube they suggested or use some else?
    Charles
  12. I use plastic resin for lay ups. Hard bond,...

    I use plastic resin for lay ups. Hard bond, long open time, and no creep. The down side it take a little longer to cure
  13. That is correct Bill, CBN are Cubic Boron Nitride...

    That is correct Bill, CBN are Cubic Boron Nitride not diamonds so you can’t sharpen carbide tools. I think most recommend running them on a slow speed grinder, so 1750 rpm is what I would use. ...
  14. Replies
    34
    Views
    6,566

    Looks like you are close to saw dust. What size...

    Looks like you are close to saw dust. What size blade will it use?
  15. There are people on here that can help you more...

    There are people on here that can help you more so than me. I would guess experiment on the bottom to get the results u want. Also after putting on finish cover it above the surface, Apx 6”,...
  16. I put washers under the idler to center

    I put washers under the idler to center
  17. I sanded my rollers. I added washers to keep...

    I sanded my rollers. I added washers to keep them centered as I remember. Need to look tomorrow and will get back. Have you ordered the springs yet. They sell 6 in a set. I have 3 extra if...
  18. Replies
    6
    Views
    416

    Thanks , will give it a try! C

    Thanks , will give it a try! C
  19. Replies
    6
    Views
    416

    Food grade mineral oil

    I know this is a dumb question but where do you buy it. In the grocery store they have veggie oil but I donít see the food grade mineral oil. Maybe I just donít know what iím Looking at or for. ...
  20. Replies
    19
    Views
    1,144

    The hilarious thing is the stain mostly came out...

    The hilarious thing is the stain mostly came out when my wife washed it. I had the soap rubbed into it and all the other ideas as well her spray and wash. Thanks all.
  21. Replies
    19
    Views
    1,144

    Yea if I remember to wear it!

    Yea if I remember to wear it!
  22. Replies
    19
    Views
    1,144

    Worth a try. Nothing else worked. The shirt...

    Worth a try. Nothing else worked. The shirt must have some polyester in it. Oil attracts oil.
  23. Replies
    19
    Views
    1,144

    Good idea.

    Good idea.
  24. Thread: Mixol ?

    by Charles Grauer
    Replies
    3
    Views
    375

    Questions? May be none of my business, but what...

    Questions? May be none of my business, but what are you dyeing and are you using water or DNA. I have some Mixol and never used it as don’t how much or ratio to mix for what I want. Thanks,
  25. Replies
    19
    Views
    1,144

    I think I’m going to bring out a line of shirts...

    I think I’m going to bring out a line of shirts for messy woodworkers, There will be one with cherry stain blotches, one with walnut Stain blotches, one for red oak, You get the idea. It may...
Results 1 to 25 of 40
Page 1 of 2 1 2