Search:

Type: Posts; User: Andrew Hughes; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.28 seconds.

  1. Replies
    14
    Views
    395

    I agree with everyone. Relying on glue and will...

    I agree with everyone. Relying on glue and will power will not work.
    Stainless steel fasteners can be quite attractive.
  2. It pretty common for Hot tar roofers to clean up...

    It pretty common for Hot tar roofers to clean up with diesel fuel at the end of the day. I remember seeing the laborers use their bare hands for mastic work. I know of one laborer that was diagnosed...
  3. Replies
    53
    Views
    2,110

    I was flashing back to some of the used jointers...

    I was flashing back to some of the used jointers I’ve seen. Mostly Craigslist ads.
    Never assume the knives in a used jointer that hasn’t been set buy you are correct. I’ve seen knives too thick,too...
  4. Replies
    53
    Views
    2,110

    No worries Doug I wouldnít throw away the guard. ...

    No worries Doug I wouldnít throw away the guard.
    Itís the original to the machine Made in Grand Rapids Michigan.
    Itís really a really long PorkChop.

    Good Luck
  5. Replies
    53
    Views
    2,110

    For me it’s just keep the knifes sharp. When...

    For me it’s just keep the knifes sharp.
    When the feed pressure goes up I start thinking about when to swap them out. Most of the time I sit in a chair in front of my machine and pass wood over the...
  6. I also own a domino itís a great tool. I also...

    I also own a domino itís a great tool.
    I also keep it under lock and key and my cute dog is all grown up. ;) Just in case anyone is getting any crazy ideas.

    Good Luck
  7. Awww you wood grinders with your first world...

    Awww you wood grinders with your first world problems.:p
  8. Replies
    5
    Views
    286

    I would be surprised if you could get any glue to...

    I would be surprised if you could get any glue to bond after linseed oil. I guess its worth a try.
    My first thought remake the door:(
  9. I donít use them either. A new sharp blade solves...

    I donít use them either. A new sharp blade solves all my bandsaw problems.
    I have a 14 pm and a 20 inch Aggi.
  10. Thread: Shop Dog

    by Andrew Hughes
    Replies
    11
    Views
    624

    My shop dog Nellie. She doesnít mind any of the...

    My shop dog Nellie.
    She doesnít mind any of the machines running but hates the push broom. :)
    She has big ears like a donkey. She can hear so well no one comes on the property without her knowing.
  11. I say both are very good Resaw blades. The RK...

    I say both are very good Resaw blades.
    The RK blade will last about 100x longer.
    If your plans are to cut expensive wood thatís just darn right precious. Wood from ď The TreeĒ then get the Resaw...
  12. Replies
    23
    Views
    1,087

    Try a single drop of water in the big dent. No...

    Try a single drop of water in the big dent. No iron or heat.
    Use something like a tooth pick to install the drop. :)

    Good Luck
  13. Replies
    7
    Views
    353

    Douglas needs to be kiln dried for furniture or...

    Douglas needs to be kiln dried for furniture or doors to set the pitch. Or when it get hot or very warm sap will weep right out of the face. Even through paint.
    Dont ask me how I know this.:o
    Good...
  14. If it happens again take the switch out but donít...

    If it happens again take the switch out but donít disconnect the wires . Turn it upside down and give it some taps with a handle of a screwdriver. Or something similar.
    My bandsaw did the same thing...
  15. Replies
    30
    Views
    1,233

    If the knifes or even one knife is too high above...

    If the knifes or even one knife is too high above the outfeed table.
    The jointer make hollow gap joints.
    Rule that out first.

    Good Luck
  16. Replies
    16
    Views
    845

    Pith off center means stress and tension in the...

    Pith off center means stress and tension in the log. One side the grain will be in compression the other side the grain is pulled. This is why limbs are terrible for resawing but good for bowls ....
  17. Replies
    39
    Views
    1,330

    I went the trade route. I hated school. I started...

    I went the trade route. I hated school. I started roofing in 1984 I also worked at a lumber yard building roof trusses I was the sawyer. I cut wood on a center line saw most have never heard one or...
  18. Replies
    38
    Views
    1,819

    Iíve found Osage Orange to be very challenging....

    Iíve found Osage Orange to be very challenging. It has soft layers between hard layers of grain.
    The wood I used for these canes was pretty stable and I liked that. I also like to use hand tools...
  19. Thatís a awesome looking table top. Itís soo nice...

    Thatís a awesome looking table top. Itís soo nice you could set them up on a couple boxes from Costco and people would say what great looking table.:)
    Everything great about a table is in the top.
  20. Replies
    66
    Views
    4,211

    Thanks not funny Mel.

    Thanks not funny Mel.
  21. Replies
    66
    Views
    4,211

    Iíve taking time to visit my work near me. Once I...

    Iíve taking time to visit my work near me. Once I built a gate out of my very best vertical grain WRC. Someone painted it purple I was so mad. I wanted to poke my finger into someoneís chest and...
  22. Replies
    66
    Views
    4,211

    Not sure if itís been mentioned yet but there is...

    Not sure if itís been mentioned yet but there is a upside to using Pva glue for laminations.
    Its not very expensive and the glue doesnít damage your handtools and jointer knives.
    I learned my...
  23. White oak is such a nice wood to work with. I...

    White oak is such a nice wood to work with. I just love the smell.
    This is a nice pic you captured Mike.
  24. Replies
    13
    Views
    1,060

    Very good tutorial Mike. Box making is one of my...

    Very good tutorial Mike. Box making is one of my favorite projects.
    These small quadrant hinges from Rockler are pretty inexpensive. I like them because they hold the lid up and open.
    They do take...
  25. Probably should leave there as a reminder to not...

    Probably should leave there as a reminder to not force together wood when gluing up panels.
    Sorry to be blunt some things just cannot be fixed.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4