Search:

Type: Posts; User: Allan Ferguson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    7
    Views
    1,697

    Very nice work and design. A great deal of time...

    Very nice work and design. A great deal of time and effort go into making something like this. A fellow segmenter.
  2. Replies
    18
    Views
    4,937

    The nova Cole jaws fit over the bed.

    The nova Cole jaws fit over the bed.
  3. Replies
    18
    Views
    4,937

    214, 360, 684, 1020, 1440, 2160, 2880, 3600. ...

    214, 360, 684, 1020, 1440, 2160, 2880, 3600. Bought 3/2009.
  4. Roger, sent a P M, or at least tried to.

    Roger, sent a P M, or at least tried to.
  5. Replies
    2
    Views
    834

    It appears that you may have some segments with...

    It appears that you may have some segments with exposed end grain, with some tear out . Useually segmented turnings have long grain exposed, hence no end grain to contend with. Also possibly moving...
  6. Replies
    9
    Views
    2,009

    Looks very good, lathe and bowls. Your present...

    Looks very good, lathe and bowls. Your present position could be a fire hazard with the base board heater.
  7. Replies
    16
    Views
    3,316

    See my response to Trying to decide on new tool...

    See my response to Trying to decide on new tool rest. This page.
  8. Replies
    17
    Views
    3,803

    The Robust Comfort rest 12" is my most used rest,...

    The Robust Comfort rest 12" is my most used rest, 1 St finger rides against the rest. I do a lot of bowls . I have the low 12" profile rest and find it very useful for finials were you can bring a...
  9. Replies
    9
    Views
    1,590

    Bill B. Is right on. Sometimes that is not...

    Bill B. Is right on. Sometimes that is not possible. Then track down a turner in your area.
  10. Replies
    4
    Views
    1,302

    The rings are maple and Paduk . If you are...

    The rings are maple and Paduk . If you are working with a block of wood, you can cut off a slice from what would become the top. Glue in the colored layers making sure that all surfaces are flat...
  11. Replies
    4
    Views
    1,302

    Walnut pot

    5 1/2" dia. poly finish.
  12. Replies
    10
    Views
    2,735

    you can mount a laser pin by making a wood...

    you can mount a laser pin by making a wood adapter attached to your bar.
  13. Thread: Box Set

    by Allan Ferguson
    Replies
    3
    Views
    1,256

    Finished with General Finishes Wood Turner's...

    Finished with General Finishes Wood Turner's Finish. It is a water based finish. Wood sanded to 400 grit, with lathe turning at 300 rpm applied 1st coat with paper shop towel folded. Let dry and...
  14. Thread: Box Set

    by Allan Ferguson
    Replies
    3
    Views
    1,256

    Box Set

    5 1/2" diameter Claro Walnut box set. Box Elder burl lid on the right.
  15. Replies
    27
    Views
    8,442

    I have done three sets. I like the challenge...

    I have done three sets. I like the challenge they present.
  16. Replies
    12
    Views
    2,066

    Looks very good.

    Looks very good.
  17. Replies
    12
    Views
    2,066

    Don't know if I was much help, but you seem to...

    Don't know if I was much help, but you seem to have it whipped into line and close to the finish.
  18. Replies
    3
    Views
    975

    There are four matching patterns in the feature...

    There are four matching patterns in the feature ring. If the ring were higher the patterns would look different. The upper half is taller than intended distorting the form which was none to good to...
  19. Replies
    3
    Views
    975

    Feature Ring Playground

    11" x 6" vessel of Makore and hard Maple.. What is to like and what is not? Put your thoughts forth.
  20. Very nice work on a complex design. I think the...

    Very nice work on a complex design. I think the bottom is distraction for what little it is worth.
  21. Replies
    12
    Views
    2,066

    Draw the crosses as you are thinking with some...

    Draw the crosses as you are thinking with some differing proportions. Decide on the one you like the most and what is do able. Feature ring is usually at the widest point in the piece. Looks...
  22. Replies
    12
    Views
    2,066

    Using the second photo, I would suggest making a...

    Using the second photo, I would suggest making a ring at the height of the cross piece, and trimming the two segments that butt against cross piece to fit. Then the next ring as you have been doing. ...
  23. Replies
    12
    Views
    2,066

    Without a drawing of your layout (plan) I can not...

    Without a drawing of your layout (plan) I can not be of help. Can you get a photo of such plan and post it. Then perhaps I or others can offer advice.
  24. Replies
    9
    Views
    2,057

    I have the motor you need. Did an up grade...

    I have the motor you need. Did an up grade several years ago. In good running order. Located in eastern Washington. You may have had excessive belt pressure . PM me for more info.
  25. Replies
    14
    Views
    4,705

    Pushing out trees can cause ring fracture, making...

    Pushing out trees can cause ring fracture, making the wood worthless for turning.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4