Search:

Type: Posts; User: Larry Frank; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    19
    Views
    359

    Hopefully, two hours a day. It depends on how...

    Hopefully, two hours a day. It depends on how bad my back is that day. I took up the scrollsaw so I had time in the shop sitting.
  2. I think Roundup should be used with caution but...

    I think Roundup should be used with caution but not scare. I have clothes I wear outside when using it. For me, I use a tank sprayer and typically use about 3-4 gallons when I spray. I am careful...
  3. Replies
    19
    Views
    338

    Well done!

    Well done!
  4. Replies
    38
    Views
    5,518

    Sticky: The real thanks goes to Rid Sheridan..he was a...

    The real thanks goes to Rid Sheridan..he was a genius with it.
  5. Replies
    12
    Views
    408

    I believe that Menards can get you the 8" pipe if...

    I believe that Menards can get you the 8" pipe if you have one near you.

    I think you would be fine with 6" pipe and still be pulling a real 1,800+ cfm with no problem.

    I considered what size...
  6. Replies
    6
    Views
    507

    You need to be a contributor to send messages. ...

    You need to be a contributor to send messages. However, it may be different with Keith.
  7. Replies
    25
    Views
    1,489

    I have been buying tools for 50 years for my...

    I have been buying tools for 50 years for my shop. I have bought and sold on Craigslist and everywhere else and will buy used when I can. I probably have over $12,000 in tools bought over many...
  8. Replies
    7
    Views
    464

    Elegant piece with great finish on it.

    Elegant piece with great finish on it.
  9. Replies
    22
    Views
    1,222

    I have the Veritas medium shoulder plane with the...

    I have the Veritas medium shoulder plane with the knob and love it. I have hand and wrist problems and the knob works great.
  10. Replies
    20
    Views
    1,037

    Not a fisherman but fascinating to see how this...

    Not a fisherman but fascinating to see how this is done.
  11. Replies
    24
    Views
    788

    I would replace the tires. The tires are damaged...

    I would replace the tires. The tires are damaged and are likely to get worse and throw and ruin a blade.
  12. Replies
    10
    Views
    773

    I know there are positive and negative reviews on...

    I know there are positive and negative reviews on it. I really like mine and a good value.
  13. I believe it is bituminous asphalt and yes...

    I believe it is bituminous asphalt and yes difficult to remove.
  14. I make a plate from pressure treated wood and...

    I make a plate from pressure treated wood and caulk it to the brick and then just mount the hose bib to it. Worked out very well for ten years and still going fine.
  15. Replies
    8
    Views
    694

    I am a contributor but have chosen to see the...

    I am a contributor but have chosen to see the ads. They are small and not intrusive and provide a small amount back to the Creek.
  16. I did rough shaping with the die grinder and then...

    I did rough shaping with the die grinder and then a 1" drum sander in a electric drill. I had drum grits from 40 to 220 grit.

    I did use a Kutzall rasp for somethings but it was hard on my...
  17. I used a DeWalt die grinder with a fine Kutzall...

    I used a DeWalt die grinder with a fine Kutzall burr for shaping.

    412807
  18. Replies
    10
    Views
    813

    Moral of the story is to find a really good...

    Moral of the story is to find a really good doctor. With technology today, they can get a great image of a herniated disk. Unfortunately, they can not always isolate what is causing back pain.
    ...
  19. I am glad you are happy with your testing. ...

    I am glad you are happy with your testing.

    Traverse testing locations are based on equal areas and not equal distance.

    The only good way to do the testing is with a long test duct to get...
  20. Good questions about doing a traverse. When I...

    Good questions about doing a traverse. When I tested using that instrument, I did a traverse multiple times. Also, to get accurate measurements, you must do it in a straight section of pipe. ...
  21. I did not find much at all. My wife found a...

    I did not find much at all. My wife found a vacuum cleaner for me to use.
  22. Replies
    29
    Views
    1,291

    Only one singer I would pay to see....Garth Brooks

    Only one singer I would pay to see....Garth Brooks
  23. Replies
    4
    Views
    511

    I bought a HF and it was terrible and got hot...

    I bought a HF and it was terrible and got hot quickly. The DeWalt that I bought was great and used a Kutzall burr with it shaping a rocking chair.
  24. Replies
    14
    Views
    729

    You should be able to get the the 6" DWV pipe and...

    You should be able to get the the 6" DWV pipe and fittings at Menards at a reasonable cost. That is where I got mine for my 5 hp DC.
  25. Replies
    31
    Views
    1,740

    I borrowed John Lanciani's instruments and made...

    I borrowed John Lanciani's instruments and made measurements of my system allowing of course with static pressure and amps. It was quite a big job to set up a test pipe and jigs to do repeatable...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4