Search:

Type: Posts; User: Scott Winter; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.21 seconds.

  1. Replies
    22
    Views
    2,526

    Thanks for all of that info!

    Thanks for all of that info!
  2. Replies
    22
    Views
    2,526

    Wire from main panel > subpanel

    I need to install a subpanel in my workshop garage since my main panel is on the other side of the house, and it wouldn't make sense to run a few hundred feet of Romex.

    I am trying to figure out...
  3. Sadly it isn't just finding people to produce,...

    Sadly it isn't just finding people to produce, but getting their hands on the raw materials :(
  4. I would think anything #5 and up would make a...

    I would think anything #5 and up would make a fine shooting plane. Even a low angle jack makes a good shooting plane.
  5. Replies
    24
    Views
    2,470

    Yes mineral spirits

    Yes mineral spirits
  6. Replies
    44
    Views
    6,142

    I do appreciate everyone's input. I was thinking...

    I do appreciate everyone's input. I was thinking 100 Amp in case I decided to get an EV down the road.

    Maybe 60 Amp makes more sense, and down the road I can run a line off my main breaker if I...
  7. Replies
    44
    Views
    6,142

    100amp Subpanel Wiring

    Hey all,

    I made a post about a week ago regarding the electrical situation in my attached garage. To run all of my new power tools I'm going to need to run a 100amp subpanel into my garage (have a...
  8. Replies
    23
    Views
    2,822

    I appreciate both of your comments. So I...

    I appreciate both of your comments.

    So I decided to do a little investigating, and I actually have access behind my main fuse box via a crawl space. There is definitely plenty of access to run a...
  9. Replies
    23
    Views
    2,822

    Table Saw and DC on a 15amp Fuse

    My new table saw & DC are getting delivered next week.

    Table saw pulls 15amp @ 115v or 7.5amp @ 230v
    DC pulls 12amp @ 120v or 6am @ 240v

    I'm sure I would definitely run into problems with...
  10. Replies
    8
    Views
    1,801

    Yeah I am definitely looking at my overall big...

    Yeah I am definitely looking at my overall big picture. I can deal with a table saw, but as it has already been mentioned in this thread you're going to need to have a dedicated DC system taking up...
  11. Replies
    8
    Views
    1,801

    Hobbyist: Kreg Adaptive Cutting System?

    I am really trying to come up with a cost effective setup that also meets my needs. I came across the Kreg Adaptive cutting system, and it seemed to check off a lot of boxes. None the less how things...
  12. 1/2" Electric Impact Gun (great for when I need...

    1/2" Electric Impact Gun (great for when I need to pull the tires off my car)
    Oscillating multi tool
    Chisel set that I use when I don't want to damage my good ones
    SAE and Metric ratchet wrenches...
  13. Replies
    59
    Views
    7,618

    Definitely not scared off!! :) A little...

    Definitely not scared off!! :)

    A little change between when I posted until right now. My other (better) half put the kibosh on the DW735X for now since we have a baby on the way in two months....
  14. Replies
    59
    Views
    7,618

    Help me decide on a table saw

    All,

    Well I am 2 weeks from moving into my new home where my 2 car garage (approx 20'x20') will be my new "man cave". I'm probably going to dedicate the one side for my woodworking area, and the...
  15. Replies
    12
    Views
    4,895

    Also the Wahuda has 4 sided inserts versus the...

    Also the Wahuda has 4 sided inserts versus the two for the Rikon model.
  16. Replies
    5
    Views
    1,452

    Thank you so much for the information. If I do...

    Thank you so much for the information. If I do end up going this route I'll definitely talk the person down some.
  17. Replies
    5
    Views
    1,452

    Used Delta 36-725 Table Saw

    I am going to go look at a used Delta 36-725 off of Craigslist. Seems there aren't many decent cabinet saws in my area on the 2nd hand market, and this one is listed for $400 which I am sure I can...
  18. Replies
    14
    Views
    2,535

    How would you rate this for a hobbyist...

    How would you rate this for a hobbyist woodworker? Where would you say the limits of this would be?
  19. Until you need to use it somewhere you don't have...

    Until you need to use it somewhere you don't have easy access to a plug. I would never go back to a corded drill unless maybe a specialty one like an impact drill that I may not use that much.
  20. Replies
    14
    Views
    2,535

    Thoughts on this Rikon 8" Jointer

    I'm beginning to assemble my hobbyist wood shop, and am researching jointers. I came across this one from Rikon, and wanted to see if anyone had any feedback on it? I can't seem to find any reviews...
  21. Replies
    74
    Views
    6,963

    Yeah I have definitely made up my mind about...

    Yeah I have definitely made up my mind about getting a SS. Now I am really considering if the PCS is a little overkill for my needs, or if I would be better off just getting the contractor version...
  22. Replies
    74
    Views
    6,963

    You guys rock. I am going to keep re-reading this...

    You guys rock. I am going to keep re-reading this post and trying to figure out exactly the path I want to take. I set myself a $5k budget more as a placeholder, and I am not opposed to go over/under...
  23. Replies
    74
    Views
    6,963

    That's a fantastic point, Jim! I might zero in on...

    That's a fantastic point, Jim! I might zero in on the first 2-3 projects instead of just the first one. They're all on the "honey-do" list, so none are optional :D

    I guess technically my first...
  24. Replies
    74
    Views
    6,963

    Used will definitely be my first avenue of...

    Used will definitely be my first avenue of choice! I live in Lancaster, PA so there is a pretty high woodworking population here.
  25. Replies
    74
    Views
    6,963

    $5k is my starting budget. I do plan on adding to...

    $5k is my starting budget. I do plan on adding to my shop over time. I would like to begin making end tables, and work my way up to a coffee table, and eventually a dining room sized table.
    ...
Results 1 to 25 of 58
Page 1 of 3 1 2 3