Search:

Type: Posts; User: Sean Moore; Keyword(s):

Search: Search took 0.00 seconds.

  1. Preferred method for jointing shop sawn veneer??

    What is everyones preferred method for edge jointing shop sawn veneer? I have several sheets approx. 65" long that I need to joint together for a seamless edge. Its pretty good off the jointer but...
  2. Removing glue stains from corners-best method?

    What is everyones preferred method of removing glue stains from corners or inside edges? I have never found a good method. Even after taping up the joints and carefully removing the tape, I find that...
  3. Cant get Jointer to cut straight, advice needed!

    So I posted a few days ago about not being able to get my jointer beds properly aligned on my new combo machine. After many people chimed in about shimming the infeed table, I've gone ahead and...
  4. Correct, the outfeed table is fixed. There are...

    Correct, the outfeed table is fixed. There are adjustments on the left (user side) to adjust its height, but unfortunately there is no way to adjust the height on the right side of the machine where...
  5. I ordered some brass shim stock on Amazon, it...

    I ordered some brass shim stock on Amazon, it should be here by tomorrow so I will attempt to shim the infeed table hinge side and report back.

    It seems that the hinge is a round bar that sits in...
  6. Hey Kevin, the hold down latch is that out of...

    Hey Kevin, the hold down latch is that out of focus handle. My issue is that even with the adjustment bolts, I cant get the bed level enough, there is a consistent down slope from the cutter. I just...
  7. So if my bed slopes down from the cutterhead as...

    So if my bed slopes down from the cutterhead as seen in the picture below, I should just add a shim under the lowest bolt? That seems like an awfully large shim to have to insert in there?

    457053
  8. Hi Eric, Where exactly would a shim go? Im not...

    Hi Eric,

    Where exactly would a shim go? Im not sure how to go about inserting a shim here.
    457050

    Adjusting the bolts on the infeed side move the table up and down but not enough to get it...
  9. Hi Steve, Im located in Los Angeles.

    Hi Steve, Im located in Los Angeles.
  10. HELP-Cant set Jointer Outfeed/Infeed Table Heights w/ Tersa Knives

    Hi all,

    I recently picked up a robland nx410 combo machine, and I have been having a hard time getting the outfeed/infeed tables adjusted.

    The machine only seems to have adjustments on the left...
  11. Replies
    6
    Views
    971

    Sealing soft edges of redwood table

    I recently built a desk for a client and they specifically wanted the desk out of redwood. I procured a nice redwood slab from a local source and the desk came out great. I finished the desk with a...
  12. Ive never enjoyed using the euro guard. I feel...

    Ive never enjoyed using the euro guard. I feel like I always get a bit of snipe at the beginning of a board as my hand rides over the guard and there is a subtle change in pressure. Also, face...
  13. Convert Jointer Guard from European bridge style to American Porkchop Style

    Has anybody ever converted their european style jointer guard to an american style? I recently upgraded to a Robland NX410 Pro and have a 16" jointer with the european bridge guard, and I absolutely...
  14. Hey Wakahisa, The problem with adjusting those...

    Hey Wakahisa,

    The problem with adjusting those bolts is that if the left most bolt that touches the cast iron (the upper red one that you circled), it catches when I lower the jointer table back...
  15. Aligning Rip Fence on Sliding Table Saw

    Hi all,

    I just purchased a new Robland NX410 Pro Combo machine. I finally took delivery of the unit last week and have been slowing getting it all set up. The instructions are quite abysmal, and...
  16. Replies
    12
    Views
    1,043

    Thanks everyone for the advice! Im going to look...

    Thanks everyone for the advice! Im going to look into getting the spindle moulder handbook. Im really only interested in cutting tenons and grooves with the shaper, hence me wanting to pick up the...
  17. Replies
    12
    Views
    1,043

    Just got a shaper, need advice!

    Hi everyone,

    I recently ordered a Robland NX410 combination machine, which includes a slding table saw, jointer/planer, and a shaper that I am eager to start using. That being said, ive never used...
  18. How do one man wood shops move large/heavy pieces?

    Ive been building furniture as a side hustle for a few years now out of my garage. In the past couple years, ive built several fairly sizeable pieces, such as a dresser and record cabinet. Both being...
Results 1 to 18 of 19