Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.19 seconds.

  1. Replies
    3
    Views
    167

    You have to be extra careful when "dropping" a...

    You have to be extra careful when "dropping" a piece of wood onto a moving blade or cutter. It is best to have stop blocks in place to prevent any chance of kickback or self feeding. It is best to...
  2. Replies
    9
    Views
    385

    Before you go to all that trouble look at the...

    Before you go to all that trouble look at the back side of the front frame where the staples are attached and the edge of where the staples pulled out. If either or both of those surfaces are...
  3. Replies
    4
    Views
    230

    I got tired of playing that game with them and...

    I got tired of playing that game with them and dropped the service. So far I don't miss it.
  4. Replies
    15
    Views
    649

    I would approach it slightly different. I would...

    I would approach it slightly different. I would glue up all the center rib pieces to make them double thickness. Then I would attach one half of the long cross pieces to the end of each center rib...
  5. I have similar shutters on my house and it is...

    I have similar shutters on my house and it is very difficult to pull out those pins without damaging the siding. If I were to remove our shutters which may happen soon due to fading, I would drill...
  6. Replies
    9
    Views
    478

    It is very difficult to get new concrete to bond...

    It is very difficult to get new concrete to bond to older concrete and the color may never match. If you spread salt on concrete to get rid of ice it is likely to spall down the road. The only cure...
  7. Replies
    4
    Views
    841

    Now that the cut is complete and you are...

    Now that the cut is complete and you are recalling the risk it is time to more fully equip your shop with push sticks and push blocks. I keep several different sized and types of push blocks near my...
  8. Excellent work, are you going to let the...

    Excellent work, are you going to let the grandkids play with it??
  9. Replies
    11
    Views
    710

    Why are you running a thin kerf blade on a...

    Why are you running a thin kerf blade on a sawstop saw. They have plenty of Hp to handle a full kerf blade. I run a full kef Glueline rip blade on my 1 Hp saw with no issues even when ripping...
  10. I can't tell from the photo if the cross pieces...

    I can't tell from the photo if the cross pieces in the frame sides are end grain of the shelves or long grin pieces making up the frame. If they are the ends of the shelves you should have no issues...
  11. Replies
    56
    Views
    2,669

    If the dark green/blue thing all the way to the...

    If the dark green/blue thing all the way to the right in the photo is the suction opening of the pump you are starving the pump. It is completely improper to reduce the pipe size on the inlet of a...
  12. Replies
    8
    Views
    541

    In the dark blue bar across the page near the top...

    In the dark blue bar across the page near the top is a tab called "Forum Actions". Click on the tab and you will see the options of: "Mark Forums Read", "General Settings" and "Edit Profile". If...
  13. Replies
    21
    Views
    806

    Apply UHMW tape to the clamping faces. Wood glue...

    Apply UHMW tape to the clamping faces. Wood glue won't stick to it and it is durable.
  14. Replies
    14
    Views
    675

    I needed new bird netting to fit over the frame...

    I needed new bird netting to fit over the frame of our bird guard. I switched to 1 inch mesh knotted nylon netting instead of the plastic 1/2 inch bird netting. What I have now is the same netting...
  15. Replies
    23
    Views
    1,092

    Which blades are you using? Try the Progressor...

    Which blades are you using? Try the Progressor T234X blades or the T101B blades both will give you smooth cuts, and use the orbital feature so the sawdust can clear out of the cut better. Just...
  16. Replies
    14
    Views
    675

    Ours are just starting, but they are hanging like...

    Ours are just starting, but they are hanging like bunches of grapes from most of the branches. There is going to be a ton of them.
  17. Replies
    27
    Views
    1,495

    I have two Ryobi L&G tools, a hedge trimmer and a...

    I have two Ryobi L&G tools, a hedge trimmer and a string trimmer, both 40 volt. I've had the string trimmer for a couple of years and I am pleased with it. I just purchased the hedge trimmer, which...
  18. Replies
    15
    Views
    929

    I would use either keyhole slots with screws or...

    I would use either keyhole slots with screws or steel pins into the studs.
  19. Replies
    20
    Views
    1,788

    My understanding is that the pins need to be...

    My understanding is that the pins need to be green wood so they will flex as they are driven in and riven pegs are better than sawed pegs.
  20. Replies
    7
    Views
    881

    Have your electrician run a 40-50 amp sub-panel...

    Have your electrician run a 40-50 amp sub-panel with 240 volt capability to your garage, then adding outlets in the future will be much easier and less costly.
  21. It is probably one of the interlock switches with...

    It is probably one of the interlock switches with a dirty contact. Next time it won't start try actuating one switch at a time then attempt to start the lawn mower. The last switch you touched will...
  22. I like working with hickory as well. I've made...

    I like working with hickory as well. I've made numerous picture frames, a complete bedroom set (pedestal bed frame with storage drawers, two large dressers, bookcase headboard and a night stand) and...
  23. Replies
    9
    Views
    666

    Buy a hanger bolt of the appropriate thread size...

    Buy a hanger bolt of the appropriate thread size and screw it into a short length of dowel.
    460859
  24. Nice looking hickory and cabinets.

    Nice looking hickory and cabinets.
  25. Replies
    13
    Views
    949

    Nice work. I made a two dish holder for our dog...

    Nice work. I made a two dish holder for our dog when he was a pup. I recently figured out an attachment that keeps him from pushing food out of the bowl with his nose.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4