Search:

Type: Posts; User: Steve Jenkins; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. If they have phone numbers listed try calling...

    If they have phone numbers listed try calling rather than emailing
  2. Replies
    5
    Views
    187

    If you’re not used to European machines bottom...

    If you’re not used to European machines bottom left is stop that locks in when pressed. Turn it slightly clockwise and it will pop back out to allow it to run.
  3. Replies
    16
    Views
    563

    My biggest complaint with wenge is you can’t...

    My biggest complaint with wenge is you can’t hardly look at it without getting splinters. I’ve done some bent laminations with no problem but nothing radical. The first time I used it years ago I...
  4. Replies
    4
    Views
    462

    Are you going to be in Arlington next week?

    Are you going to be in Arlington next week?
  5. Replies
    17
    Views
    1,375

    Josh, just curious if you solved the jointer...

    Josh, just curious if you solved the jointer problem.
  6. Replies
    17
    Views
    1,375

    Where are you located? Maybe someone is close...

    Where are you located? Maybe someone is close enough to stop by and give you a hand.
  7. Look for 16/4 mahogany rather than 4x4

    Look for 16/4 mahogany rather than 4x4
  8. Replies
    8
    Views
    413

    Most common cause is bottoming out the bit in the...

    Most common cause is bottoming out the bit in the collet. For the collet to tighten properly there has to be a little space for the bit to be pulled in as it’s tightened
  9. Replies
    14
    Views
    694

    Brush flashing from roll-up door installation...

    Brush flashing from roll-up door installation company
  10. Replies
    76
    Views
    5,792

    I’ve been self employed since 1982. It’s tough...

    I’ve been self employed since 1982. It’s tough but rewarding in ways other than financial. One thing I’ve noticed is how much entrepreneur sounds like “ I tripped in manure”.
  11. Replies
    13
    Views
    778

    It sounds like the slides aren’t set even front...

    It sounds like the slides aren’t set even front to back either in the cabinet or on the drawer
  12. Replies
    48
    Views
    3,027

    Also certainly woods is a good source for veneere

    Also certainly woods is a good source for veneere
  13. Replies
    48
    Views
    3,027

    Thanks again for all the compliments. It is...

    Thanks again for all the compliments. It is veneer with a solid edge.
  14. The dark curved areas look like it was swiped...

    The dark curved areas look like it was swiped with a damp rag prior to staining so absorbed more stain
  15. I can’t speak to phenolic but I know that adding...

    I can’t speak to phenolic but I know that adding a “cool gun” from MSC when milling 100’s it feet of oak and maple rope molding increased time between sharpenings about 10-15 times. I was using a...
  16. If you have to use pliers or a pipe wrench put it...

    If you have to use pliers or a pipe wrench put it on the metal ferell (sp) rather than the wood
  17. Replies
    30
    Views
    1,375

    I would go with the suggestion to rip the...

    I would go with the suggestion to rip the backsplash off a Home Depot or Lowe’s counter top
  18. Replies
    10
    Views
    732

    This thing is big and heavy enough it would need...

    This thing is big and heavy enough it would need a pallet plus not being sure whether or not it works I wouldn’t want anyone to put money into shipping
  19. Replies
    10
    Views
    732

    I don’t think it would work as a room...

    I don’t think it would work as a room dehumidifier. It doesn’t really have a blower it needs compressed air passing through it.
  20. Replies
    10
    Views
    732

    Oops I knew it is a dryer. Don’t know why I said...

    Oops I knew it is a dryer. Don’t know why I said cooler
  21. Replies
    10
    Views
    732

    Just thought I’d give this a bump before I haul...

    Just thought I’d give this a bump before I haul it off to the dump
  22. Replies
    10
    Views
    732

    Refrigerated air cooler

    Free for the taking. No shipping. Zurn General Air Division
    Model R10A mfg. 3/85
    110v single phase, 11.2 amps 50 scfm
    Iíve no idea if it works or not. It was given to me and I never even...
  23. Replies
    12
    Views
    815

    Also to help maximize thickness rough cut length...

    Also to help maximize thickness rough cut length of parts prior to any milling. I usually cut 1/2 to 1” long after cutting off all end checks.
  24. Glad to hear it

    Glad to hear it
  25. Curious if you found a solution that worked or...

    Curious if you found a solution that worked or did you have to sand
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4