Search:

Type: Posts; User: Thomas Wilson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thanks John and Paul. I was pretty sure John...

    Thanks John and Paul. I was pretty sure John would be ahead of me on this idea. Paul, I realized that since I am not planning to put sheetrock on the inside of the DC closet, the wires will have to...
  2. Electrical Connections for Dust Collector Motor Control Box through Wall or Floor.

    I am in process of getting a new Oneida dust collector and placing it in the basement below the main shop floor. I have tested the remote from my current duct collector from the basement to the...
  3. Replies
    35
    Views
    1,296

    I agree with John too. My 2hp does not keep dust...

    I agree with John too. My 2hp does not keep dust level below the level that irritates my lungs. I have to wear a mask for most stock prep. I am going to upgrade to the 5 hp Smart Gorilla. But if...
  4. Replies
    9
    Views
    590

    The VCI paper is volatile corrosion inhibitor. ...

    The VCI paper is volatile corrosion inhibitor. The purpose of the ziplock is to keep those volatiles from escaping. I don’t think the oily paper towel would help. Have you checked your...
  5. Wouldn’t miss it.

    Wouldn’t miss it.
  6. Replies
    9
    Views
    590

    My condolences. Some suggestions. Get a temp...

    My condolences. Some suggestions. Get a temp and humidity with high/low memory. You can get two for about $20 on Amazon. This will help you keep track of rust causing conditions. On most iron...
  7. Replies
    35
    Views
    1,296

    In answer to the Oneida vs ClearVue question, the...

    In answer to the Oneida vs ClearVue question, the 5hp Smart Dust Gorilla is variable speed and generates more flow against resistance than a conventional single speed fan like the 5hp ClearVue. If...
  8. Replies
    35
    Views
    1,296

    Lots of good advice here. If you find you have...

    Lots of good advice here. If you find you have to stay within your $3-5L budget, you can probably live with a 2hp cyclone collector and duct system for two or three multi-purpose drops. You would...
  9. I have two shops. The machine tool one is in a...

    I have two shops. The machine tool one is in a stand-alone building near the lake cabin. The hand tool shop is in the condo in the city. The hand tool shop is strictly to be neighborly about...
  10. Hi Zane, My air filter is the JDS AirTech...

    Hi Zane,

    My air filter is the JDS AirTech 2000. The manual is a single 11x17 sheet printed on both sides and folded in half.

    I scanned the two sides into a single pdf file. I scanned at 300...
  11. I think this is the model of JDS air filter that...

    I think this is the model of JDS air filter that I have. I will check tomorrow and bring the manual home to copy if it is the right one.
  12. I missed the original release of these projects. ...

    I missed the original release of these projects. Good as new for me. Thanks.
  13. Replies
    18
    Views
    1,864

    An 18 panel can cut safely on a typical cabinet...

    An 18 panel can cut safely on a typical cabinet table saw. The trick is to turn the miter gauge so it runs backwards in the slot. You would need a fence on the miter gauge and clamp the workpiece...
  14. Replies
    18
    Views
    1,864

    An arrangement like Derek’s but clamp a scrap...

    An arrangement like Derek’s but clamp a scrap piece on the blow out edge to support it. If you have an end vise and bench dogs, use that with a slightly shorter piece of plywood underneath. Put...
  15. Replies
    63
    Views
    3,604

    Axel, I find myself looking forward more and more...

    Axel, I find myself looking forward more and more each day to your posts. Thank you for the obvious effort you put into sharing them. Who is your photographer? I thank them as well.
  16. Replies
    9
    Views
    657

    “If you give a mouse a cookie…”. Tom, you are a...

    “If you give a mouse a cookie…”. Tom, you are a kind and gentle soul if you are trying to save a mouse.

    For me, it amazes me that mice can lick the peanut butter off the trip paddle of a...
  17. Replies
    21
    Views
    2,115

    This style of table is frequently used as the...

    This style of table is frequently used as the project for introduction to woodworking. It serves in this case to rewire your woodworking brain to work in your new temporary shop without your sliding...
  18. Replies
    54
    Views
    9,262

    You are still increasing your lead, Christopher. ...

    You are still increasing your lead, Christopher. I am still working on dust collection. That design doesn’t look big, but it has a huge amount of storage. Good job.
  19. Replies
    16
    Views
    1,156

    Bora Workbench Casters work well. I attached a...

    Bora Workbench Casters work well. I attached a set to 2x6’s and clamped them to the bench rather than attaching permanently. I posted about it on this...
  20. Thanks everyone. I had forgotten about the...

    Thanks everyone. I had forgotten about the Magport. That is a good alternative. I don’t think I will be swapping the planer and router connections back and forth a lot. I tend to set up to do all...
  21. Quick Fit clamp or Dust Right to swap hose between machine

    I am pruning my ductwork plan and am going to share a hose between planer and router table. Can I swap using the Quick Fit clamps or should I get something more specifically designed for routine...
  22. Replies
    18
    Views
    1,284

    Now I know how to get you to come visit.

    Now I know how to get you to come visit.
  23. Replies
    18
    Views
    1,284

    My shop is in the woods so the potential is...

    My shop is in the woods so the potential is always there for snakes. So far I have only seen one tiny one, the size of a pencil, which I swept out the door. We have water snakes that live on top of...
  24. Some other folks around here will have to up...

    Some other folks around here will have to up their production substantially to fill the need for entertaining content. We should give a little back to entertain you as you convalesce. But I hope...
  25. My solid, prefinished, white oak flooring has...

    My solid, prefinished, white oak flooring has tracks from 15” Powermatic planer and 3hp Sawstop ICS. I have factory casters on both. Both of these tools are much lighter than your slider. I just...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4