Thanks everyone for your input! My thinking was I should disconnect it, but wanted to be sure this was the right move. As several of you mentioned, I was concerned about the bearings on the...
Type: Posts; User: john brady; Keyword(s):
Thanks everyone for your input! My thinking was I should disconnect it, but wanted to be sure this was the right move. As several of you mentioned, I was concerned about the bearings on the...
Hi All,
I apologize if this should be in the General Woodworking and Power Tools section rather than Turning, but I though it would be more familiar of a subject here. I think I know what I...
Hello All,
First let me start off by defining what I mean by the term "GOOD" in my topic title... I need a chuck that will actually CENTER the bits when closed. You would think this would be a...
Hi guys, Thanks for your suggestions!
Paul, I did want to get an OIL-LESS pump. I noticed some of the cheap pumps didn't state what type they were.
Chris, Thanks for the photo's (especially...
Hello All,
I've been trying to research vacuum pumps for setting up a vacuum chuck system on my lathe (Laguna Revo 18|36). I thought I'd find some information here, but I only found one post...
Well, this is my THIRD attempt at trying to add another reply to my post. I lost the first one this morning after the power went out just before I was ready to post. Then I lost it again when I...
Hello all!
I want to replace my aging table saw, and I'm looking at the saws in the $1,000 range. After comparing several saws in this range, I'm considering purchasing the Grizzly GO833P. I...
Hi Bruce,
Thanks for taking the time to reply, and posting the instructions. I already found how to order, but was hoping John (or anyone else) that ordered the Grizzly pulleys already might be...
Hi Guys,
I know this threads is several months old, but wanted to ask how John (Rosser) made out with his Grizzly parts? Did you get any? If so, did they fit OK?
One of my Spindle Pulleys...
Hi Guys,
Thanks everyone for taking the time to respond. Dave-- thanks for the details-- it was VERY helpful. I'll get some contact cleaner and give that a try. Since the grinder isn't used...
Hi Rod,
Yes, I did do that. My son suggested I take them, but I didn't know what to do with them once I had them. I also wasn't sure the reading would be accurate since the pot was defective (I...
Hi Guy's,
Thanks for taking the time to help! I guess I'll just add another coat of the latex paint then. I thought maybe the Poly might dry/cure harder than the paint giving better protection. ...
Hello All!
This forum (General Woodworking & Power Tools), seemed to be the closest one for my question. I have a Delta GR250 6" variable speed grinder that I purchased a little over 10 years...
Hi Robert,
I used Minwax water base poly (with the BLUE label) on maple faced plywood for a shelving unit nearly 15 years ago and it hasn't yellowed yet!
John
Hello all!
I'd like to know if it's OK to apply water base polyurethane over (100%) latex acrylic?
I made a set of doll bunk beds for my granddaughter. She wanted a specific paint color that...
Hi Guys,
Thanks for the suggestions! I applied a little grease to each of the shafts and it really helped a lot-- I can move the lever with one hand now (I use to need two hands to reduce the...
Hello All,
During a search for belt replacement help, I found that a few folks here have this model Delta lathe. I just had to replace the belt on mine, and before I put the cover back on, I...
Hi Jim,
Based on what you've said, I'm pretty sure going the "ISO" route will be your best and easiest way to go.
Download UltraISO here:...
Thanks for the suggestions! After the suggestions, I was hoping the holes might fit to my metal vise, but it didn't. Guess I'll keep it with the metal vise, maybe it will come in handy some day.
...
Hi Jim,
I delved into that a while back... AND it can get VERY Confusing and FRUSTRATING! There are several issues you have to deal with:
1.
What was the DVD made with? Not all "Home" DVD...
They changed the penny?
Now they already said that it costs MORE money to make a penny than a penny is worth. So now they go and spend MORE money on making a NEW one?!
GOOD GOD what a...
MS probably "borrowed" theirs from Evernote. LOL...John
Hi Bill,
There is a feature in Windows that most people don't know or ever use, but I always show it to my elder challanged computer clients.
(in Windows) click START > Programs > Accessories...
Hi Mike,
I live in South Central PA in a gated community on a lake. We're priviledged to have a nesting pair as residence.
I've also seen them frequently while fishing on the susquehanna...
Hi Scott,
It's most likely because they are considering the church the same as a business. I ran into a similar issues a few years back. I had cable at home and paid $xx for it. Wanted to get it...