Search:

I back flush my filters and duct the exhaust dust outside. I have to wait for a west wind because my wife got upset when the wind blew the dust over the patio.

Well no luck on the moving the fan back Rich and I have a bearing splitter but the bearing is too far back, the bearing is partially covered by the fan, no room to fit the splitter between the two....

This has been kind of a long process, I purchased a new motor motor and conversion kit several years ago and the 16" impeller a couple years ago and just now getting around to building the blower....

Plus one on the MET, we spent a day there and even my wife, the pharmacist, was impressed with all the American furniture. I took gobs of photos, no flash allowed so take some faster lens for the...

I used OSB aluminum foil backed on the walls and ceiling, attached with screws, in my 3rd stall workshop. A little reluctant to paint it as with my basement workshop, I had to remove some OSB more...

Has anyone talked to Sean about his retrofit? I see this thread is 2 1/2 yrs. old and I don't see any follow up since he re-installed the table. He also talked about making one of these for a friend...

I would recommend you go visit Bill Pentz's web site, before you purchase any meters. It is free and he has done a lot of the leg work. I managed the R&D department for a very large HVAC manufacturer...

Not going to say, my wife might see my post.

I am curious, how big a bandsaw are we talking? I have a Rockwell 20" with a Woodslicer blade, a 2hp motor and it resaws 12" oak like butter. Granted I don't hog it through. This thing must be huge.

I have been piece mealing mine also, I purchased the cyclone off the net that Joseph referenced, I am guessing 4 to 5 yrs ago. I have mounted to the top a 2hp Grizzly DC that my wife got me for...

I've kind of had that for a number of years. I cut my plywood and rough saw my lumber, to a convenient length, in my garage and then plane, joint, final saw, rout etc in the basement. I then convert...

I am in the process of installing an exhaust vent system for my woodworking shop. My ceiling is 9' 6", I will have radiant heat in the floor, air conditioning, and I am in Michigan. The intake will...

Ditto with Matt, I use wire lube to insert the flex into a coupling or other fitting then fasten the two together with 3-1" sheet metal screws through the coupling and flex hose. I have mounted to...

I ordred one last weekend. I looked all over for a good used drill press but then decided on a new one and chose the Delta, liked the 6" quill and the range of speeds for wood or metal. We will see...

I have a quick one, I finally got around to running a 6" line to my garage for my planer. My unit came with a 4" dust port. I want to convert it to a 6" dust port. Did you do it in metal or wood? If...

My mistake, I from time to time toy with the idead of switching one of my jointers or planers to a helical cutterhead. And the number that stuck in my head I thought was like $450 for my G0490. When...

Found this on Ebay for $349 + $30 shipping from WoodPRO out of Independence, Oregon. What do you think?


Here is what they claim:

This 8” spiral cutterhead replaces your standard straight...

I have a G0490 Grizzly parallel bed jointer. And it was a brute getting it off the truck in 2 pieces. I purchased it new from Grizzly. I saw that one on CL here in GR and it seems a little pricey for...

Every other stud 2 with 2 alternate circuits 20 amps each on every other receptacle. Lights have one switch on a separate circuit. 20 amp power cord on reel hanging from the ceiling. Compressor and...

Have been working on a end table project with some left over mahogany from an entertainment center I built in 05. I re-sawed the mahogany (I paid $10.00 bf.ft.back then) into about .100" thick veneer...