Search:

Type: Posts; User: Rod Sheridan; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.68 seconds.

  1. Replies
    28
    Views
    2,250

    Thanks Roger, I found a local dealer and will try...

    Thanks Roger, I found a local dealer and will try the product……Rod
  2. Sounds like a story to me. There’s a global...

    Sounds like a story to me.

    There’s a global shortage of shipping containers and extremely high shipping volumes now….Rod
  3. Replies
    28
    Views
    2,250

    I almost exclusively used solvent based finishes...

    I almost exclusively used solvent based finishes and didn’t like the look of water based polyurethane finishes.

    Then I found a Minwax oil modified polyurethane and it looks very much like oil...
  4. Replies
    28
    Views
    2,250

    Naphtha should not be used as a solvent, the...

    Naphtha should not be used as a solvent, the flash point is dangerously low and it can be absorbed via inhalation of vapours or by skin contact.

    Regards, Rod
  5. Replies
    29
    Views
    1,574

    Don’t worry, she doesn’t understand you either.

    Don’t worry, she doesn’t understand you either.
  6. Replies
    19
    Views
    745

    Bruce, 10,000 cars is an outstanding achievement,...

    Bruce, 10,000 cars is an outstanding achievement, thanks for being so generous with your time….Rod
  7. Replies
    19
    Views
    745

    Thanks Paul, good luck on your kitchen...

    Thanks Paul, good luck on your kitchen renovation….Rod.
  8. Replies
    19
    Views
    745

    Thanks Jim, I already have a “job jar” full of...

    Thanks Jim, I already have a “job jar” full of items, boredom isn’t on the horizon…Regards, Rod
  9. Replies
    19
    Views
    745

    Well, I retired at the end of June and have...

    Well, I retired at the end of June and have finally made it into the shop this week.

    I am making a book box for the front garden, completely self serving as I hope to reduce my book...
  10. Hi, my first suggestion would be to replace it...

    Hi, my first suggestion would be to replace it with a short stroke slider, safer, more accurate and more capabilities.

    My next choice would be a Sawstop for safety, however it has the failings of...
  11. Replies
    53
    Views
    2,128

    Why do cars look alike? Mathematics. ...

    Why do cars look alike?

    Mathematics.



    Physics determines the shape of the vehicle for passenger automobiles as one of the main drivers of design is fuel efficiency.

    Regards, Rod
  12. 461326461325Hi, glad that you are happy with the...

    461326461325Hi, glad that you are happy with the new machine.

    My outrigger, fence and holdown clamp hang on pegboard, as does my Fritz und Franz jig.

    The edging shoe is in a little pegboard...
  13. Replies
    8
    Views
    781

    Really dull knives?….Regards, Rod.

    Really dull knives?….Regards, Rod.
  14. Replies
    27
    Views
    1,527

    All my garden tools are cordless except for the...

    All my garden tools are cordless except for the trimmer, it plugs I’m.

    My lawnmower is a push reel mower, does a great job, is quiet, no cords or batteries.

    Regards, Rod.
  15. Replies
    55
    Views
    31,597

    Sticky: Hi Woody, I sent you a PM, please email me a...

    Hi Woody, I sent you a PM, please email me a photo or drawing of your timer…..Thanks, Rod.
  16. Sorry I was assuming that you wanted 240/120...

    Sorry I was assuming that you wanted 240/120 volts.

    If you parallel the 2;generators then you would double the current and power capability….Rod
  17. Yes, the voltage will vary from zero to 240 volts...

    Yes, the voltage will vary from zero to 240 volts as the generators drift in and out of phase.

    The 120 volt loads would be fine…Regards, Rod
  18. Hi, if you’re under 1Kw with the dryer running...

    Hi, if you’re under 1Kw with the dryer running and it’s an electric dryer, there’s something wrong with your instrumentation

    A dryer is about 5Kw.

    If you want a transfer switch you move all...
  19. Hi, make a pattern then use a 1/4” straight bit...

    Hi, make a pattern then use a 1/4” straight bit to cut maybe 1/4” deep. In something to use as template.

    Now saw the board in half, then trim flush on the router or shaper.
    Now you have 2...
  20. Replies
    23
    Views
    1,418

    Yes, exactly how I set them up. Regards, Rod

    Yes, exactly how I set them up.

    Regards, Rod
  21. Doug, 25% is pretty good. Big engines are...

    Doug, 25% is pretty good.

    Big engines are about a 1/1/1 energy balance (without co-generation) which gives 1 unit of work, 1 unit of heat rejection out the exhaust and 1 unit out the water jacket...
  22. Replies
    105
    Views
    9,483

    A week ago I mentioned this to a friend who is...

    A week ago I mentioned this to a friend who is much older than me, his response was surprising

    "You graduated and yet you can't read Latin. When I graduated from high School we needed a basic...
  23. Yes, as Steve invited loosen th nut inside the...

    Yes, as Steve invited loosen th nut inside the table a bit then move the nut outside the table a small amount in the correct direction.

    Snug up the inside nut and check.

    Regards, Rod
  24. Hi Dennis, that may be considered hard usage,...

    Hi Dennis, that may be considered hard usage, check your owners manual for recommendations.

    In your case it may be more of a calendar limit than a mileage limit….Regards, Rod
  25. Replies
    11
    Views
    645

    I have a deep Milwaukee AC portaband. It cuts...

    I have a deep Milwaukee AC portaband.

    It cuts pipe, Unistrut, angle iron, threaded rod etc.

    Regards, Rod
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4