Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.27 seconds.

  1. Replies
    26
    Views
    541

    I was going to mention this one but you beat me...

    I was going to mention this one but you beat me to it. I can not figure out if it uses propriatary batteries. The old GE lawn tractors use regular 12 volt car batteries.
    Bill D
  2. Replies
    13
    Views
    276

    You should be able to buy a used one for about...

    You should be able to buy a used one for about $100 and sell it after for the same price.
    Bil lD
  3. What is under the wood?

    What is under the wood?
  4. I bought a used Buzz box welder at a yard sale...

    I bought a used Buzz box welder at a yard sale for a good price. I could not get it to weld a consistent bead. Finally opened it up and found ground and one hot lead had been reversed. So the case...
  5. Replies
    16
    Views
    395

    Railroad, like snow sheds? Bill D ...

    Railroad, like snow sheds?
    Bill D

    https://thetahoeweekly.com/2019/05/snowsheds-protection-of-trains-over-donner-summit/
  6. Replies
    12
    Views
    403

    Most anywhere in the world buried conduit will...

    Most anywhere in the world buried conduit will gradually condense water and get filled with liquid water.
    Bill D
  7. Replies
    9
    Views
    560

    Could be for a router as well but, in my...

    Could be for a router as well but, in my experience, those always have two arms.
    Bill
  8. I there enough slack to remove one link? ...

    I there enough slack to remove one link? Motorcycle shops have chainbreakers bigger then bicycle shops. Farm stores bigger yet.
    Bill D.
  9. Replies
    12
    Views
    533

    8 amps #14 is fine. It may be cheaper to replace...

    8 amps #14 is fine. It may be cheaper to replace the entire cord with one longer one. I doubt the existing male end can be reused? If not you will have to buy two cord ends to make a extension...
  10. Replies
    16
    Views
    395

    Climate in your country?

    Climate in your country?
  11. Replies
    21
    Views
    567

    When I had to hold a cast iron sink up to install...

    When I had to hold a cast iron sink up to install the rimless trim I used a screw jack centered under the tailpipe. If the cyclone is sturdy enough I would put a piece of plywood across the bottom...
  12. If the insert screws are rusted in place that...

    If the insert screws are rusted in place that could be a problem. They are probably under a cover and never saw direct rain. You may have to shatter the insert to remove the screw on a few.
    Rusted...
  13. Replies
    25
    Views
    2,998

    Also very useful on a drillpress. Umbrella lamp...

    Also very useful on a drillpress. Umbrella lamp is another search term.
    Bill D
  14. Replies
    6
    Views
    393

    What are the little extensions on the back end of...

    What are the little extensions on the back end of the feet? Look to me like metal afterthoughts because the chair would tip backwards.
  15. Replies
    4
    Views
    290

    It rots fast outside. Corkscrews as it drys. ...

    It rots fast outside. Corkscrews as it drys. 99% chance it is red or blue gum if it grew in California.
    Bill D
  16. Replies
    5
    Views
    424

    Could a Grizzly spindle be modified in a machine...

    Could a Grizzly spindle be modified in a machine shop to fit?
  17. CBN does not have diamonds so it can be used on...

    CBN does not have diamonds so it can be used on iron and steel with little wear and no need for flood coolant to protect the wheel.
  18. I used the link I did because I could not find it...

    I used the link I did because I could not find it on the Starrett web site. I guess it is no longer made. Shapers and planers become obsolete around the 1970's when steel mills started selling a...
  19. Replies
    11
    Views
    512

    Is this Bradford pear?

    Is this Bradford pear?
  20. a picture might help. planer/shaper gauges can...

    a picture might help. planer/shaper gauges can be had for cheap. Just make sure they have at least one screw on height pin thing. Better if they have a set spanning a good range.
    Bil lD.

    look...
  21. Replies
    14
    Views
    612

    I bet that 150 was a typo? Hottest it has ever...

    I bet that 150 was a typo? Hottest it has ever been here is 120 degrees. maybe you mean in the attic?
    I do not work in the shop at those temperatures since it has no AC. Above 100 I only stay in...
  22. [QUOTE=Matt Day;2950187]Your original switch...

    [QUOTE=Matt Day;2950187]Your original switch likely will not work with the VFD. If it’s a mag switch it won’t work, it needs to be like a light switch, which by the way, a light switch works fine. I...
  23. Remove the starter but use the switch station to...

    Remove the starter but use the switch station to control the VFD. You may have to program the VFD to allow remote operation not just control from the touchpad. Do not set the deceleration below 3...
  24. Replies
    26
    Views
    1,052

    Mine is a 35 gallon cardboard drum with some kind...

    Mine is a 35 gallon cardboard drum with some kind of plastic liner.
    Bill D.
  25. There is a joke here about the light only works...

    There is a joke here about the light only works when the door is open. There is no way to check the switch to see if it goes out when closed. Unless you recruit a small baby.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4