Search:

I have an old Epilog 24TT whose mother board is dead. Replacements not available. has anyone fitted an alternative controller to an epilog laser? it seems such a shame to scrap the machine while the...

I have an EXT 40 watt Epilog. I have not used it for a couple of weeks. I started a new job, the tube was not firing-it often takes a minute to get going. The machine suddenly moved the main beam Y...

Started building the OGA Dinghy at the end of February. Beginning to look good now.428141428142

Hi All,
Sorry but i think I also posted this in the wrong place.
I expect this has been asked before but the site search doesnt work? I have returned from 3 weeks holiday turned on the laser and...

Hi All,
I expect this has been asked before but the site search doesnt work? I have returned from 3 weeks holiday turned on the laser and the machie would not register home and a message xy...

Hi all on the forum. I have an epilog EXT 35 watt machine that has just started playing up. When I have switched the machine on at the start of a day some times it starts with the axis disabled....

Ran a few jobs today and all was just fine. I then got an email from a company in the UK that had one in stock. It was the same as the one i removed from the 24tt except th the output is 65 watts...

Just did a quick fit of the ATX93 psu and it boots up just fine. Need to run a few jobs through to check. Mother board seems ok all LED's light up as they shoud. Certainly beats having to buy a...

Hi Amos thanks for your answer.

It is indeed the 3.3v,5v,12 supply that has gone. Found a 0.22ohn resistor also blown on the old board. Made byPowDEC. THis link...

Just having major problems with my 24TT. I switched it on and heard like a fuse going. Epliog reckoned the mother board gone. Couldn't see anything wrong. On further investigation I noticed a...

When using the Epilog I usually have the red dot pointer on. I have noticed that some times it appears in a different part of the mirror on the end of the x axis bar. Thought nothing about again...

Blagging very much a UK term I think. The police coming out perhaps.

Frank have PM'd. you .

This site is so refreshing where people help each other freely when ever needed. Gives faith in the...

This really is such a brilliant site. So informative and every one is so helpful. I am still quite new lasering but learning fast with the help from the creek. Can any one help me out here please?
...

I spoke to a Chris at Identify(UK) and followed his suggestions. Set the Dpi to 150 and try again. This showed the individual laser paths quite clearly on acrylic. I was vescoring a triagular shape....

Thanks for the suggestions Frank.

I have cleaned everything, regreased the x axis etc. I have atached an image of what I mean. The left hand side of the engraving has the ragged edge. It is...

I have just picked up a job that means rastering on glass tumblers. I have just noticed that the quality of the rastering is a bit odd. There are occasionally sections where the glass has not been...

Hi all. I have liiked through the past posts to see if I could find an answer to my problem. No luck.

I bought some 3mm mirror acrylic a couple of months ago. Today I wanted to cut out some animal...

Thanks for your reply Frank. The two pinions are "in time".Not a belt problem. Without taking the panels off it would appear that the table runs on 4 rollers each side running in tracks . The...

Thanks for your reply Frank. The two pinions are "in time".Not a belt problem. Without taking the panels off it would appear that the table runs on 4 rollers each side running in tracks . The...

I posted a problem I am having with my 24TT last week refering to the low power / weak engraving on the left side of the table. I would have thought that it would have been better there as the laserr...

I have an Epilog 24 TT which I use a lot for rotary work. It works well. Today a was trying out engraving photos on to acrylic. I noticed very quickly that the image was not being engraved on the...

I have found that the glasses direct from the manufacturer will slip when I set them up in the rotary without the hold down wheel. They just will not grip the drive wheels. The solution I found was...

Watch out for this rather obvious scam. Vendor said the machine was new. Would not let me see it / pick it up. He was too busy etc,etc

http://london.craigslist.co.uk/bfs/804540966.html
...

Hi,
Can any one give me some help here. I have set up a sheet of acrylic and got 10 awards to raster on a sheet 24 x12. All going OK until 3/4 down the work i started to get lines engraved across...

Hi all.
A couple of weeks ago I posted her about the troubles I was having with my 24TT. Having beein in touch with Epilog service centre I have the machine running better than ever. A new tube was...