Search:

404126Just wanted to follow up on this thread, machines delivered in late November. We have been very happy with the new job control process. Learning the new interface took us only a few days to be...

So job control is running on one PC connected to the 3 machines? I'm guessing we just open two job control windows, one for each laser?

I appreciate any & all comments & suggestion in advance. Please except my apologies as a long time lurker who doesn't post. I've committed to purchasing two Speedy 300's to replace my aging M-300's....

I have found the most repeatable, time saving and accurate way is to let the laser make the plaque for you. Draw the plaque. I draw the repeatable plate with holes. The holes are typically undersized...

I put a piece of brass plated steel engraving material down & then use small magnets to hold the laserlights in place atop the steel.

I use thin glue from http://www.etchedstone.net, I believe and will confirm. Initial bond is pretty quick at under 15 seconds.
I mostly attach crystal and glass to marble bases with just a single...

I gave up & went the easy route. I purchased the proprietary Corian adhesive gun & tubes. Looks much better, the adhesive doesn't show any bubbles. It does shrink slightly but that will be taken care...

I have been laser engraving & painting solid surface signs for years but would like a smooth finish for endurance & maintenance on an upcoming order. I have a potential job for 600 pieces, exposed to...

I would stop by and talk to Engraving System Support in Dade city FL who sell & service Universal. As a high volume awards shop I have zero time for analyzing machines, repairs or communicating with...

I use both Signlab and Corel x5. Corel runs the lasers and sublimation processes along with graphic intensive artwork. Signlab for lasers, rotary engraving and vinyl plotting.
In my opinion signlab...

Trust all installed GMS modules gives options, mine was set to medium & I turned it down to low, the lowest setting, still doesn't load automatically. Delay load is selected as it is on your screen...

http://www.discount-trophy.com/

Joseph, does the macro still work after you close Corel and reopen? I have the button but the gms file needs to be manually found and opened every session.

Discount Trophy carries an 8"x8" Item # DTGL6 in Blue & DTGL8 in Red not exactly the same but meets most of your criteria.

c\program files\corel\coreldrawgraphicssuitex5\programs\draw\gms
The file doesn't appear in the macro manager, I have to search and select the file.


Copied from other thread.
I have downloaded...

It appears we are having a similar issue, I posted two hours ago in an older thread. Hopefully someone can coment.

Bumping an old thread for updated information.
I have downloaded & installed the braille macro on my 32 bit vista system running X5. The translate button is visable but doesn't work unless I...

I vector cut the material and then apply paper by lining up sheets on a sunny window. The cut will yellow or burn along edges with to much power. Hold sheet down with magnets to help with curling....

Another possible issue is the electrical connection to the table motor. The connector shorts out, disconnect and look for black burn marks. All of my lasers have had this issue after three to five...

I wonder if they changed the coatings. My silver comes out looking just like a piece of black non laserable 12x24 stock aluminum.

I did 250 in black & was not happy with the contrast. I found cleaning up with mineral spirits did brighten the engraved area somewhat but the base metal does not appear to be "bright".

246843

I replied not sure where the post went. Does anyone else have issues with this bulletin software? I can't seem to use the back button to go back to the tread list page after selecting one thread....

Peeled the factory brown paper mask, applied my vinyl & paint. No crazing, excelent durability & resistance to lifting when using a mask.

I never use my plotter to cut resists unless I'm dealing with a complex shape that need to be applied in multiple pieces to conform to the shape of the object. Instead I use a vinyl resist & stick it...

I learned the hard way about painting acrylic sheets. Our project involved masking 4x8x.75 acrylic masked with vinyl in the reverse. After cutting hundreds of names in vinyl, weeding & then...