Search:

Type: Posts; User: Scott Memmer; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. True, Richard, but you've likely never heard of...

    True, Richard, but you've likely never heard of this material. It's called DuPont Vespel and is the most expensive plastic in the world. Pricing? For a sheet 10" x 10" x 1/4" = $1350.00. It was...
  2. Hi, Peeps, I'm bumping this thread. I usually...

    Hi, Peeps, I'm bumping this thread.

    I usually buy off Amazon, and I'm having trouble finding a Lenox blade to fit my little WEN 9-inch wheel machine. I'm placing a link below from another site. Is...
  3. Jim, thanks. Good ideas all the way around. I'm...

    Jim, thanks. Good ideas all the way around. I'm returning the cheapie lamp to Amazon and will indeed contact the resin manufacturer about natural sunlight curing.

    Take Care, Jim,
    Scott
  4. Funny, I was thinking that too, Jim. I'm in Los...

    Funny, I was thinking that too, Jim. I'm in Los Angeles. Do you think 15 minutes on a sunny day would do it?

    Thanks,
    Scott
  5. Jim, hi, thanks. You're always a great...

    Jim, hi, thanks. You're always a great respondent. Appreciate your post.

    As you might have suspected, this would put me way over budget for this project at this point. I'm in prototype phase on...
  6. Hi, All. Can Somebody Please Recommend a Top Quality Curing Lamp for UV Resin?

    Hi, Everyone. I use UV-curing resin in my shop, usually not much thicker than about 1.0 mm (.040"). I occasionally put some green tint in it, which makes it more opague and thus more challenging to...
  7. Jim, Carl & Tony: Sounds like a winner. Thanks...

    Jim, Carl & Tony: Sounds like a winner. Thanks for your posts.

    Scott
  8. Richard, agreed. However, as my OP stated, I'm...

    Richard, agreed. However, as my OP stated, I'm cutting almost 100% industrial plastics, not metal. However, high-end engineering plastics like PEEK were designed to replace metals. Therefore, they...
  9. Your Recommendations for a Durable Bandsaw Blade

    Hello, Everyone. I don't cut wood but metals and industrial plastics (Delrin, Ultem, PEEK). I am seeking a durable, long-lasting bandsaw blade. I am using a basic 9-inch Wen two-wheel machine rigfht...
  10. Agreed, Jim, and understood. BTW, even stranger,...

    Agreed, Jim, and understood. BTW, even stranger, I'm putting these PSA pads on a 12-inch lapmaster lapping machine. Yeah, I know, bizarre.

    Scott
  11. Thanks for the tip, Alex. sm

    Thanks for the tip, Alex.

    sm
  12. Bruce, thank you very, very much. I knew someone...

    Bruce, thank you very, very much. I knew someone on here would know a source for this.

    Appreciate it,
    Scott
  13. Seeking 12"-Inch PSA Pad at 800 or 1000 Grit.

    Moderator: I'm not sure if this post belongs in this subforum. Please move it if it fits better somewhere else.

    Hi, Folks. I have a need in my manufacturing business for a 12-inch PSA (not hook...
  14. Hi, Jim, thanks for your response. I can agree...

    Hi, Jim, thanks for your response.

    I can agree to all those conditions, and my pours are very shallow (less than 1.0 mm / .040"), but what puzzled me was this slow-setting Epoxy STILL hasn't...
  15. John, hi. Actually, we bought that material with...

    John, hi. Actually, we bought that material with the pattern built-in, 6000 miles away. We scour the planet for cool stuff.

    sm
  16. Maurice, sorry for my delay in getting back....

    Maurice, sorry for my delay in getting back. Busy, busy.

    I like epoxy and don't mind using it. What I'm struggling with is an epoxy that gives me an adequate amount of set time and dries clear and...
  17. Hi, Everyone. I'm slammed in meetings all day,...

    Hi, Everyone. I'm slammed in meetings all day, but wanted to acknowledge your responses and let you know that I'll get back on here within 24 hours. Thanks so much,

    Scott
  18. Seeking Suggestions For a One-Part Glue to Replace Epoxy

    Howdy, folks. I've laser-engraved this product, then filled it with epoxy colored with mica powder. Is there a glue out there that dries clear that I can use for this job instead of epoxy? All the...
  19. David, hello. I see your post here, but I can't...

    David, hello. I see your post here, but I can't locate either a PM or email anywhere.

    Thank You,
    Scott
  20. Jim, Howdy. So kind of you to post and offer some...

    Jim, Howdy. So kind of you to post and offer some possible assistance. I'm going to PM you right now.

    Jim, it would probably be faster and a better use of our time to email back and forth, if...
  21. Needing Advice & Assistance on a CAD Drawing and CNC Services

    I haven't been on this wonderful forum in many a month. but it's good to be back. I have a project involving CNC machining with which I need help.

    I manufacture a series of products for the...
  22. Lee, thank you. I'm going back to a 1/4" blade,...

    Lee, thank you. I'm going back to a 1/4" blade, to see if I can get that size to work. I'm familiar with the tracking/alignment knob from previous bandsaws. I'll report back tomorrow.

    Thanks...
  23. Doug, hi, thanks for your post. I may have no...

    Doug, hi, thanks for your post. I may have no been clear in a previous post. I did have a broken blade, but it was a 59-1/2" x 1/4" blade. I bought some of the same size to replace it, but they...
  24. Steve, will do, thanks. I could almost swear that...

    Steve, will do, thanks. I could almost swear that I pulled all the way down and triple-checked it, but I'll try it again. I loosen it so much that the handle came off completely, so I can't imagine...
  25. Hey, Rod, thanks so much; that makes a lot of...

    Hey, Rod, thanks so much; that makes a lot of sense.

    One last question, if I may. The WEN model I have was recently discontinued. The model # is 3939T. The direct replacement in the WEN line...
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4