Search:

Type: Posts; User: Lewis Justis; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.21 seconds.

  1. Replies
    4
    Views
    942

    Take a look at the FOG (Festool Owners Group)...

    Take a look at the FOG (Festool Owners Group) website. Workbenches built from 8020 are a huge topic for discussion there.
  2. Replies
    11
    Views
    3,518

    Michael, I built a cabinet for the machine to sit...

    Michael, I built a cabinet for the machine to sit on. It has drawers for bit and clamp storage, an open bay in the cabinet for the cooling water system, and an open bay in the cabinet for the...
  3. Replies
    63
    Views
    9,369

    This may have already been suggested, but they...

    This may have already been suggested, but they work very well:
    https://www.shopcartsusa.com/Product-PanelHandler.html
  4. Replies
    40
    Views
    4,644

    Phil, very nice work! The ebony pulls really...

    Phil, very nice work! The ebony pulls really complement the cherry.
  5. Replies
    40
    Views
    4,644

    Thanks everyone for the great discussion and good...

    Thanks everyone for the great discussion and good points on both sides. As I said, I understand the challenge of keeping the content fresh. I suppose since I have been reading FWW for a long time,...
  6. Replies
    40
    Views
    4,644

    FWW Magazine Oct 2021

    I have been a FWW subscriber for nearly 35 years, so I understand that keeping the content interesting year after year is a challenge. But, I still eagerly await each new issue. So I just read the...
  7. Replies
    11
    Views
    3,518

    Ken, I purchased an HD520 back in October. New...

    Ken, I purchased an HD520 back in October. New Wave had the same deal going then with the spindle, so I have that as well. I had read a lot of negatives about the earlier models of the Shark, but...
  8. Replies
    28
    Views
    2,132

    I had a new one like that, really tight to slide...

    I had a new one like that, really tight to slide on a 1-1/4 spindle. A little white lithium grease, and it went on with no problem.
  9. I have the Jet JJP 12HH in a PortAMate PM3500...

    I have the Jet JJP 12HH in a PortAMate PM3500 mobile base. This base handles the weight of the machine well, is easy to move, and is completely stable when locked down. I have had the Jet since...
  10. Replies
    6
    Views
    2,065

    Sam, chances are good that your spindle is 3/4",...

    Sam, chances are good that your spindle is 3/4", but those shapers also had a 1/2" spindle available too. You can measure the spindle with calipers to be sure. The book mentioned by the others is...
  11. Replies
    7
    Views
    1,423

    Do some research on Richard Poyner, who was a...

    Do some research on Richard Poyner, who was a slave, bought his freedom and became a famous chairmaker in Franklin, TN.
  12. Replies
    15
    Views
    3,714

    My shopvac had the on/off pushbuttons. When the...

    My shopvac had the on/off pushbuttons. When the on switch stopped working, I took it apart and the contacts were burned. I went to Radio Shack and bought a rocker switch with the same voltage and...
  13. Replies
    9
    Views
    1,118

    I went to the Lie-Nielsen hand tool event in...

    I went to the Lie-Nielsen hand tool event in Nashville Saturday morning, and then on to the Fall meeting of the Cumberland Furniture Guild at Greg Pennington's shop/school where he gave a...
  14. Replies
    7
    Views
    1,249

    Looks like some used ones for sale on amazon:...

    Looks like some used ones for sale on amazon:
    https://www.amazon.com/American-Woodworker-Magazine-June-Issue/dp/B001Q4J8TS
  15. Replies
    7
    Views
    1,910

    I believe the late Danny Proulx was the author. ...

    I believe the late Danny Proulx was the author. He wrote a column in Cabinetmaker magazine and wrote several books.
  16. Replies
    4
    Views
    1,136

    It is made for that bench (Sjoberg Elite) with 1"...

    It is made for that bench (Sjoberg Elite) with 1" diameter dog holes in a top that is about 3-1/2" thick.
  17. Replies
    11
    Views
    1,845

    I was there yesterday. Yes, venue was smaller,...

    I was there yesterday. Yes, venue was smaller, parking limited, and fewer vendors. But it seemed to me that the crowd was pretty good. Hammer (Felder) was there with a combo machine and a bandsaw....
  18. I went with the Grip-Tite system years ago and...

    I went with the Grip-Tite system years ago and haven't regretted it. There is a precision-ground steel plate that I screwed to my Biesemeyer fence and magnetic featherboards. I also have this...
  19. For my 3hp Unisaw, I prefer the Forrest WW II (I...

    For my 3hp Unisaw, I prefer the Forrest WW II (I have 4) for just about everything. Keep them clean and they last forever.
  20. Remember, Stanley is responsible for...

    Remember, Stanley is responsible for buying/selling -off, and ultimately destroying what we knew as Delta.
  21. Contact cement is the best adhesive for this...

    Contact cement is the best adhesive for this task. Coat both the laminate and the substrate (mdf or plywood) and let dry. Space out 1/4" dowel rods 12-18" apart on the substrate, then lay the...
  22. As others have said, Sears sold that machine as...

    As others have said, Sears sold that machine as well as table saws, drill presses, and lathes built by AMT. They were built out of cast iron and sheet steel stampings. They were also sold direct...
  23. Replies
    21
    Views
    4,301

    Take a look at Cabinet Planner. It may be just...

    Take a look at Cabinet Planner. It may be just what you are looking for.
  24. Replies
    16
    Views
    3,017

    On Saturday, went to the spring meeting of the...

    On Saturday, went to the spring meeting of the Cumberland Furniture Guild and heard Don Williams speak on the Studley Tool Chest and also on finishing.
  25. I believe that is the OEM guard of the most...

    I believe that is the OEM guard of the most current model Delta Unisaw.
Results 1 to 25 of 41
Page 1 of 2 1 2