Search:

I call that the Bermuda Triangle factor. Need it, then you don't see it. Looking for something else? The 1st search item shows up in plain sight.

When something just slides off, using a 4 pound hammer to drive it back on is not a prudent decision. Driving on items with bearings can cause brinelling of the balls in the bearing at a minimum, and...

Did you replace the bearings? Did you replace the brake? If you got the wheel off, there should not be a bearing problem getting it back on. Suggesting that something you replaced is causing the...

Lots of recommendations for something else, and if you read my post, I already bought the Bora. Guess I made a big mistake, but planning on using it tonight to see if that is the case.

If that is the only compressor you will have, the tank is way too small. I have the smaller version that I use under my workbench for very minor air useage. But put a blow gun or impact wrench on it,...

Use it before trying to fix something that may not influence the cut at all.

I don't see any Jet 1510 models, you must mean 1015? It will be your choice as they are all very similar. With the Jet 1221 you get a 1 hp motor compared to the 1/2 hp on the 1015. 1 hp on the Rikon....

Are there any zoning laws or ordinances? Insurance issues with your carrier? Fire marshall approval? Cost to get electricity and electrical capacity you can get in a remote building? I'd look at that...

If the walnut was stored in a shed, keep a strong eye on it. If you see any small diameter holes, or piles of fresh sawdust around it, there are powder post beetles in the sapwood. Get it out of your...

You should read them a little closer, especially #1. https://sawmillcreek.org/showthread.php?298511-Initial-Complimentary-Tools-for-my-NEW-lathe&p=3200862#post3200862

I'm not a fan of laminating 2 wider boards together to make a thick beam. All are other laminations are usually a balanced glue of odd numbers of layers. I would laminate the boards in a edge grain...

Wenge and other expensive wood boxes for $5 chisels? Seems counterintuitive. Make another box out of poplar and let the box match the chisels.

I'd share a picture of my shop and how I work, but I would loose any respect I have left. If I had any to start! I'm going to be 70 in a couple months, and have been nursing a bum knee for almost a...

Maybe I didn't make the best choice, time will tell. I'm not worried about maneuverability in the shop. When I had a full time shop, we used a skate type device with 4 wheels. When the plywood was...

I store my 800 and 1200 in a rubbermaid container. I put the lid on my bench and the stone on it when I use it. It doesn't slide, but I don't push down really hard either.

How does a Crazy Horse Dolley help me wheel in plywood from my van? Looks like it doesn't fold up too small when not being used either.

I'm at the end of slinging full sheets of plywood around my cramped shop. So this Bora tool seemed like the perfect solution. Found a great sale price and placed the order at an unknown place for me....

Explaining to new woodturners that standing by a spinning block of wood is extremely dangerous is far from sensationalizing. It's a concern for their lives. I choose not to mention the incidents...

I think you will find that buying a chisel set will provide you a couple of chisels that will go into a drawer and never come out. The face shield you are looking at is very good, but will not...

Not sure that's a good idea. It's not like bondo and using it to fill tear out could easily be a problem over the years. It's only made to fill tiny wood pores. Having tear out in the first place is...

Infinity Cutting Tools make German hobels. (planes)

I set mine so it lifts the wood and moves it 1/8" forward. This gives me the sprung joint I prefer, but still makes a very flat face on the stock.

A card scraper is my tool of choice.

Do you have one, or which one did you recommend? The OP asked for a 30A and that one is rated at 30A.

I sure wouldn't want to pay their regular prices, but those sale prices look great. Free shipping from an Iowa family business, sure looks good.