Search:

Type: Posts; User: les winter; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    4
    Views
    785

    Thanks for the advice, Mike. best. les

    Thanks for the advice, Mike.
    best.
    les
  2. Replies
    4
    Views
    785

    Thanks, Tom. A bit far for me.

    Thanks, Tom. A bit far for me.
  3. Replies
    4
    Views
    785

    wtb or trade: spindle sander

    Looking to buy a spindle sander in NW New Jersey. Rikon or similar. Not ridgid, harbor freight, etc. I do have a 14" riser USA delta bandsaw to trade if that works.
    Thanks for looking.
  4. Replies
    1
    Views
    680

    WTB Sorby Tenon Sizing Tool

    Used for turning tenons on the lathe.
    thanks.
  5. Replies
    46
    Views
    6,606

    You would experience the same problem at a power...

    You would experience the same problem at a power jointer. Two flat faces are required.
  6. WTB Tapered Reamer and Tapered Tenon Cutter

    Lee Valley is backordered on the tapered reamers and tapered tenon cutter. Anyone have these for sale?
    thank you
  7. Replies
    2
    Views
    722

    PM sent. Thanks.

    PM sent.
    Thanks.
  8. Replies
    3
    Views
    875

    Sold pending receipt of funds. Thanks for...

    Sold pending receipt of funds.
    Thanks for looking.
  9. Replies
    3
    Views
    875

    Any offers?

    Any offers?
  10. Replies
    3
    Views
    875

    Stanley Bailey 5-1/2

    Stanley Bailey 5-1/2 in good user condition. Repainted inside. Handles refinished. Sides and bottom were rusted/tarnished. These surfaces have been cleaned. The sole is flat. Blade is a Veritas...
  11. Replies
    18
    Views
    2,106

    thanks Sean.

    thanks Sean.
  12. Replies
    18
    Views
    2,106

    What oil stone did you use to remove all that...

    What oil stone did you use to remove all that rust?
  13. Hello Julie. Where did you buy the Supergleit?

    Hello Julie. Where did you buy the Supergleit?
  14. FS: Delta 14" Band Saw in NW New Jersey

    USA made Delta 14" band saw with riser. Plug and play. Carter roller guides, Carter quick release tension, Griz resaw fence, cast iron pulleys, link belt, many blades, some new and one lightly used...
  15. Sent you a PM

    Sent you a PM
  16. Replies
    0
    Views
    1,351

    wtb Travisher

    Anyone have a travisher in good shape to sell?
    thank you.
  17. Replies
    4
    Views
    897

    Thanks for the input, all. Off Peter's link, I...

    Thanks for the input, all. Off Peter's link, I found one.
  18. Replies
    4
    Views
    897

    Thanks Peter. Still looking for one local or...

    Thanks Peter. Still looking for one local or willing to ship.
  19. Replies
    4
    Views
    897

    WTB: Brett Guard

    I'm looking for a Brett tablesaw guard. Not the big overarm job, but the one with the moveable mount. If only the shield is available, that would be ok. No substitutes, please. It must be the...
  20. Go out and buy a lottery ticket, Scott. Your...

    Go out and buy a lottery ticket, Scott. Your luck is running strong. We have a match. Send me a PM with your mailing address and I'll get the bar and screws out to you this weekend.
  21. Hello Scott. I may have you covered. Measure...

    Hello Scott. I may have you covered. Measure the bar length width and thickness. If we have a match, you can have what you need for postage.
  22. Replies
    53
    Views
    5,845

    On mine (4, 6, 7) I needed to treat the opening...

    On mine (4, 6, 7) I needed to treat the opening in the chip breaker as above and in addition widen the slot to fit over the lateral adjustment wheel. A thou or two does it. Dremel tool.
  23. I do not know if you can use Dawn on a Shapton. ...

    I do not know if you can use Dawn on a Shapton. I know you can on a Norton. Just a drop. Keeps things clean and easy sliding.
  24. This sounds like something I have experienced. ...

    This sounds like something I have experienced. Any oil carried over from that oil stone to a water stone caused gunk on my Norton 8000. Clean the oil off before using the water stone and gunk will...
  25. Replies
    2
    Views
    681

    SOLD Thank you.

    SOLD
    Thank you.
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4