Search:

Type: Posts; User: Brian Runau; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    14
    Views
    417

    Trying to be lazy, but I should reset and check...

    Trying to be lazy, but I should reset and check everything in the process. Thanks for being the voice of reason.

    Brian
  2. Replies
    14
    Views
    417

    Chris: It is a 735. It was set up fine with...

    Chris:

    It is a 735. It was set up fine with no snipe, I had adjusted the infeed outfeed tables accordingly. This piece was too short and the planer threw it on a line about 13 ft towards one...
  3. Replies
    14
    Views
    417

    Dewalt lunch box planner

    I have this portable planer and use it in my shop. I put a board through that was to short; and man it didn't like it much!

    Little snipe coming out of that side on the back end of the board I'm...
  4. Replies
    11
    Views
    566

    thanks men

    thanks men
  5. Replies
    11
    Views
    566

    I think there is more meat left than I...

    I think there is more meat left than I realized.420737
  6. Replies
    11
    Views
    566

    thanks guys.

    thanks guys.
  7. Replies
    11
    Views
    566

    It will be like a face frame joint. Just the...

    It will be like a face frame joint. Just the cross horizontal piece is only 3/4 " thick by 1" wide. This is the piece going between the inset drawers and at the top of the piece where it meets the...
  8. Replies
    11
    Views
    566

    festool domino ?

    Putting together two sides of a night stand. I have a leg that is 1" thick. I was planning on using the 5mm x 30mm setting on my domino and mating against this 1" thickness. Leaves @ 1/8 or 3/16"...
  9. Replies
    6
    Views
    267

    Nice work. thanks

    Nice work. thanks
  10. Replies
    6
    Views
    267

    Nightstand design

    Making a nightstand to go with this dresser. I have some left over 18" guides, but I am concerned about using them since it would make the nightstand deeper than normal. I would wind up with a...
  11. Replies
    22
    Views
    774

    Good point. Frustrating for me figuring out how...

    Good point. Frustrating for me figuring out how to do it, but you are right the hard work is done and it is a nice look than overlay drawers. Thanks.

    Brian
  12. Replies
    22
    Views
    774

    ken: it is dark walnut and I sorted the wood...

    ken:

    it is dark walnut and I sorted the wood so I would have no sap wood showing in the project. No stain with an Arm R Seal wipe on finish.

    Thanks.

    Brian
  13. Replies
    22
    Views
    774

    I did use Grass slides and dovetail boxes. ...

    I did use Grass slides and dovetail boxes.

    Thanks Brian
  14. Replies
    22
    Views
    774

    walnut no stain with Arm R seal.

    walnut no stain with Arm R seal.
  15. Replies
    22
    Views
    774

    Finished my dresser

    Picture me breaking my arm patting myself on the back. Major doubts I could actually do this and prefer not to do inset drawers on future projects, but complete. I know where all the flaws are... ...
  16. Replies
    22
    Views
    774

    Finally finished my dresser.

    Took a lot of time, first time for me with insert drawers and I think the last time.

    Brian419639
  17. Matt, sorry I can't go to anything Purdue; except...

    Matt, sorry I can't go to anything Purdue; except the girls in the day I went to Wabash! Brian
  18. thanks Bill. I can run and buy a pick up load at...

    thanks Bill. I can run and buy a pick up load at a time.
  19. I do have an 8" jointer and a planer, just under...

    I do have an 8" jointer and a planer, just under the false impression I could work with S2 lumber when in fact I can't, from my local lumber supplier. They are the only game in town for a hobbyist. ...
  20. Feel like I live in a decent lumber desert

    I live in Indianapolis and either I am terrible about milling lumber or not able to get my hands on flat sanded stock.

    I bought some walnut from Northwest Lumber. Not cheap stuff. 13/16" thick...
  21. Jim, Good morning. My fix did not solve the...

    Jim, Good morning. My fix did not solve the problem. This drawer is like a chair or table with one leg too short. It is pivoting on opposite corners and the two other opposite corners are moving...
  22. great suggestion. thanks.

    great suggestion. thanks.
  23. Figured it out. One of the catches mounted...

    Figured it out. One of the catches mounted underneath the box in front was not flat. I screwed it in at an odd angle and the ass end was raised up. This pushed the guide up when it was engaged and...
  24. I have installed the guides and mounted the...

    I have installed the guides and mounted the drawer boxes on the guides in the opening, then I am adding the drawer faces to the drawer box. Placing a shim in two places on the bottom and each side...
  25. Inset drawer face assembly on a dresser

    I am building a dresser with inset drawers and using Grass dynapro 3D guides. Top row and 2nd row went fine, but I have run into an issue on the 3rd and 4th rows. The drawer height is 6-1/2 & 7-1/2...
Results 1 to 25 of 216
Page 1 of 9 1 2 3 4