Lessons from a box build

In my on going quest to hone some skills in veneer and inlay/banding, a simple box can present a lot of learnings. I would put this box in the “ok” category. A few things to keep in mind for the next project:

If the veneer isn’t flat, take the time and effort to soften and flatten it out.

Jointing matters. “Close enough” isn’t good enough. The gap is going to get pretty magnified when finished.

Never sand ebony. Funny thing is I watched a video that said never to sand ebony, right after I had done it. That ebony dust can not be removed and gets into everything. The top was completely redone with different material.

I watched a bunch of videos with folks leveling veneer with a ROS. I won’t do that again. Take the time to hand sand. The burl veneer on the box has a few small cover ups where I went completely through it with a ROS. Or maybe the lesson is to learn to use the ROS more judiciously, or slow down the speed. I don’t know...I think it’s hand sanding from now on.

Banding miters will not swell to perfection when glued in. What you see on a dry fit will be the finished appearance. Take the time to make them right. Don’t scrimp on banding. If it doesn’t fit right, cut a new one.

Use magnifying glasses (if you’re old like me) to check fit...really makes a difference for me.

As fellow creeker Mike Henderson recommends, put tape on the trailing edge when cutting veneer. It is very prone to tear out.

A compact router is a great tool...but mistakes happen in the blink of an eye. Go slow. Practice the run with the power off first to make sure the board is secure.

And on a somewhat different subject, french polishing is truly a learned skill. I admire those that know what they’re doing. I’m getting better, but still challenged to get a feel whether to add more shellac, more DNA, more oil or what, when the vapor trail stops, or the pad gets a bit sticky. More practice needed here.

Oh, and related to all the above, french polishing will bring out every little defect in the surface. I will spend far more time and attention of this in the future.

Anyway, good fun and glad to go down this path.

Attachment 385308

That is some beautiful figure. Sounds like a good project with lots of learning built in. Boxes and other small projects are deceptive in that they look "simple" but, employ many of the techniques that other furniture projects involve. You landed on a couple things that improved my work; very careful inspection of your surface prep before finishing -and- if something isn't right, make another one. Inadequate surface prep is an easy fix, just keep going. Bad surface prep can most times be repaired but, I have learned to kinda "feel" when to stop spending time trying to fix something and "just make another one". This has saved me a lot of time and frustration as opposed to trying to repair something that is never going to look quite right ;-)

Looks a lot better then ok to me Phil. There is an awful lot going on in that box, and it looks really nice.

Thanks for the lessons-learned Phil. I always get insight from such posts. I havent tried veneer, banding or inlay but I will bookmark this post for when I get to that.

I think it's a lovely little box!
Fred

It's a great little box. Complex and well executed. I would be very proud of it.

Thanks all. It was one of those “lets see how this goes” kind of projects using what I had on hand. Admittedly, it almost went in the trash can a few times, but I kept telling myself that this is about making mistakes. Finish wise, I should have “ambered” up the sides to get a better match, but all things considered, it will make for a better execution on the next one.

Did I mention what happens when you sneeze while moving a compact router with a 3/16” bit? :eek:

Hi Phil,
Many times when making boxes, the wood grain/patterns lead to their selection as well as dictate the overall finished dimensions. I wonder which materials that you used on your wonderful box was largely responsible for the overall design and construction. Also, what are the dimensions? Thanks for sharing.

That will teach you not to be wearing your dust mask.:o

Phil,
Thanks for sharing some of your learned experiences.

Hi David,
The dimensions are 12 1/2” x 8 1/2” x 3 1/2” tall. This box was pretty much a frankenbox from materials I had at hand. I knew I was going to use the curly maple for the main box. It measured 1/2” by 48” x 3”. The dimension of this box is about the max I can get out of that length (I usually plan material need as length of box x2 + width of box x2 + 4” for the waste cutting four miters - 1”/miter). I like a continuous board so I can get at least the 3 corner grain match. The top is a small scrap piece of 1/2” birch ply that I framed with a 1/2” piece of hard maple I had as a cutoff from some other project.

I then looked around for what seemed to be complimentary to the curly maple and chose the quilted maple and redwood burl veneer from a pack of mixed veneer I had. The banding (and originally used and botched ebony/maple stringing) came from a sale at Rockler...happened to walk in a few weeks back and they were heavily discounting their banding and stringing (like $3.50 per tube), so bought everything that wasn’t broken. Just picked through that and chose the pattern where I had enough to go around the box twice as well as outline the redwood burl (and looked reasonably decent to my eye).

I’m in the process of doing a federalish style end table for my son, so this was my practice in veneer/banding/stringing.

Thanks for the nice complement!