-
8 Attachment(s)
Using up scraps
Long time ago (last Christmas..) I made a Blanket/Hope chest...with a Aromatic Red Cedar floor.....have used up most of the scraps of Cedar since then...still had a small stash left...:D
Attachment 470203
Thought about making a small box out of this mess. Cross cut saw was waiting for use...
Attachment 470205
And the only end that needed "shot" was a "Factory" end...
Attachment 470209
Thought maybe a box about this size....maybe some finger joints at the corners?
Attachment 470210
Used a 3/16" sash chisel to space the fingers, and do the chopping out...
Attachment 470211
Disston No.68 was used to saw the lines,,
Attachment 470212
Use a No. 65 to mark the baselines...
Attachment 470213
Also using some Ash scraps to help out...
Next time I meander to the shop...I'll see about getting the other 3 corners done...then see about a bottom and a lid
Attachment 470214
The SW marking gauge..
Stay tuned...:D
-
6 Attachment(s)
Well, after the shop clean-up this afternoon, decided to get some work done, as well. Re-arranged to finger spacings a bit...soon had Corner # 2 dry fitted up..
Attachment 470302
Looking a bit better, too....might as well get corner #3 done..
Attachment 470303
Which left corner #4 to do....keep getting better fits....always the first one, that doesn't quite fit....by the time I get to the last corner..
Attachment 470304
Both ends have a knot in them...but not in the same spot...
Decided a Poplar panel for the bottom will work....needed to cross cut a couple pieces..
Attachment 470305
One wasn't wide enough, yet 2 were too wide....ripped the excess off at the bandsaw. Not the straightest of rip cuts ( never is) but that's ok, as a plane will straighten that out. Need a good glue joint edge..
Attachment 470306
Clamped the 2 boards together in the vise, run the Millers Falls No. 9 as a jointer ( Size the plane to the work) and then some glue and clamps..
Attachment 470307
Bench vise acts as a 3rd hand ...and as a caul...let this sit a day...have done just enough in the shop for today..
Stay tuned...:D
-
5 Attachment(s)
Well, panel for the box's bottom is out of one set of clamps...needed edges trimmed for width....then the saw marks removed..
Attachment 470361
I wanted at least one good edge for the next step..
Attachment 470362
Where I trim the panel for length....then flatten the panel..cleaned up the glue lines, too...
Attachment 470363
then set this aside with the rest of the box parts....
Attachment 470364
Going to have some "fun" in a little bit...
Attachment 470365
Cross cut saw....Stanley No.358.
Part one of today's follies, stay tuned for Part 2...:D
-
8 Attachment(s)
Before I tore the box apart...I sized some Cedar for a lid. Intend to have finger tabs to lift the lid. Front/Back will need to be a bit wider...first. I need 2 blanks..
Attachment 470366
Then mark how much to saw off as a rip cut..
Attachment 470367
Decided a handsaw will do this job..
Attachment 470368
So, take this down from the "Ready Rack"..been awhile..a Disston 20", 10ppi, D8 ( no hyphen)....should work out just fine on this thin stock...
Attachment 470369
Saw down as far as I can, WITHOUT hitting the vise...flip around and finish the cut..
Attachment 470370
Wipe the saw down, and hang it back up...and work on getting a good glue up joint..
Attachment 470371
Then some glue mooshed around, a few cauls, and a couple clamps..
Attachment 470372
Cauls to keep things flat...as they wanted to bow up from the clamps...set this aside....and, since the glue, and the glue brush was still out....
Attachment 470373
Still had a few cauls available...
Will let both sit a day, or two..no real rush.
Stay tuned...
-
No stores open today...Christmas Exchange Party (ate way too much.) was last night....so...might meander to the shop, and remove a bunch of clamps...and hope nothing flies apart...after that?
Stay tuned...:D
Happy Holidays, people!
-
7 Attachment(s)
Well...box is out of the clamps..
Attachment 470460
Bottom was planed smooth..
Attachment 470461
All four sides were sanded and planed until smooth and squared up...then the rim around the top of the box was leveled..
Attachment 470462
Then the box was set aside while the lid was cleaned up, and squared up..
Attachment 470463
Fancy front was bandsawn...more sanding and some more plane work...while I dug out some hinges...
Attachment 470464
These came with nails?...Ahhh, I think..NOT! Will use tiny screws, instead...there is also a matching latch..
Attachment 470465
So....next time I head for the shop..I might try to install all the hardware?
Attachment 470466
Since I now have a much better (no plastic gears) pilot hole drill....
Stay tuned...:D
-
3 Attachment(s)
Well, I was just going to take a couple drills back to the shop, tonight...instead...
Fixed a Bandsaw
Re-handled a small hammer...
Installed 2 hinges...after re-drilling a few holes in the brass..
Attachment 470540
And adding a latch out in front..
Attachment 470541
And adding a first coat of varnish.....
The bandsaw's problem? Piece of...junk in the lower guide blocks....had to remove the blade to clear...running good now
The hammer? Kept wondering why the head of the small ball pean hammer kept coming loose......turns out..no wedge, and the head was on upside down...Cleaned up the end of the handle, redid the wedge's kerf and made a new wedge....and installed the head on the handle the correct way...
Had to set up a second eggbeater drill....as the hardware needed bigger holes to clear the screws (instead of nails) and had to move one location down a bit...
Attachment 470542
A Blue Stanley. Had to sharpen the bit, too.
Normally, the shop stays closed on Mondays...
BTW: Found just enough thin pieces of that cedar, to make a small tray to stash inside the box...
Stay tuned :D
-
How much cedar does a box need for odor control? Asking because I don’t know. I got a pair of house shoes to wear upstairs in front of the wood stove for the holidays. Let us say they are wool and the cat is a bit too interested in them.
I am going to make a jointed box and put a cat proof latch on it. I routinely shower downstairs after work before I come up stairs for the evening. My feet are not especially stinky.
How much cedar should I use? And now I am thinking about vent holes the cat can’t get her paws through. When they aren’t on my feet these house shoes need to be boxed, lamb is one of the cat’s culinary favorites.
Thanks.
-
Home Depot sells a carton of Aromatic Red Cedar slats..to line a closet with...or a blanket chest....or even a shoe box. Slats are 1/4" thick, T&G, about 4" wide.....I'd have to check, but..I think the slats are 48" long. Tain't cheap, either. I picked up a caryon over a year ago..as last years Christmas Exchange Gift was a Blanket Chest....with a Cedar floor. The rest being Ash.
You can rip the tongue or groove off, then rip to match the height of the box....cut a 45 on the ends, and line the sides of the box..NO FINISH. You can even line the floor of the box...will help hold the sides in place.
-
8 Attachment(s)
Ok, decided to re-do the "Dolly Parton" lid....bandsaw to rough out a new profile...then..
Attachment 470788
A chisel to refine it...the #101 plane to round-over the new edges..
Attachment 470789
Along each side, down at the bottom, are 3 brass nails. I pre-drilled through the Cedar, until I just started into the Poplar bottom panel. Then drove each nail home.
Attachment 470790
Lid looks a wee bit better? Started on a tray, tonight..
Attachment 470791
Should be enough to make a lift out handle, too. Planed all the parts, to remove the rough sawn side...
Attachment 470792
And..make sure they were all the same height..
Attachment 470793
Had just started to cut the finger joints..
Attachment 470794
When the bandsaw's blade broke...:mad:...so..
Attachment 470795
I guess that means it is quitting time!
Stay tuned :D
-
4 Attachment(s)
Up-date....will be at least a week, or two, before I can buy a new blade (or 3)....went back to the No.68...too coarse, AND I cut the wrong side of the lines for the matching end piece. Tossed that away...put the saw away...cobble a new end piece...
Attachment 470862
That was a hair too fat....Dug around on the shelves in the shop....was unable to get the old 3-wheeler bandsaw out of it's hidy-hole....however...we have ways
Attachment 470863
Hmm, once all the dust and cobwebs were removed....
Attachment 470864
Sears Craftsman (Emerson) 13" tilting table, cast iron base Scrollsaw. Was last seen back when I made a key emblem for a Key Safe box....
Used the side piece as a pattern to follow...cutting on the waste side of the lines...and even left the lines...was still able to turn the blade around in the cut...dry fit required a small hammer..
Attachment 470865
The Scrollsaw could use a smaller mouth opening....otherwise, seemed to work well enough. 1 done, 3 to go....
-
Had plumbing issues to correct, today....what we thought was a leaky hose on the clothes washer....turned out to be damaged kitchen sink drain line...where in hooks into the city line. re-connect, and fixed. Dryer vent connection will be next payday....old one was broken at the back of the dryer......didn't get around to any wood shop time, today.
Road trip tomorrow, and a Monday, to boot....might be a little bit before the tray is done.
Stay tuned..
-
Road trip to Lima, OH...final follow-up on my old legs...still have to wear special socks...otherwise, but to normal, for me..
Cause of the bandsaw blade breaking (bad?).....lower thrust bearing had frozen up....had to replace the bearing. While I have the bandsaw torn down...did some Maintenance on the area...table might even sit better, now...we'll see....as soon as I can get a new blade for the bandsaw.
Today being a Monday..shop was closed...had enough trouble with the bandsaw tear-down...need to clear off the bench, anyway...before I can do the 3 tray corners. Question being...how to attach a handle...finger joints? Sliding dovetails? Hmmm...
-
6 Attachment(s)
This being the Camel Day....gave the shop a try....needed 3 more corners cut and fitted...
Attachment 471099
End on the right is a bit too thick...will plane down, later....set the sides onto the base..
Attachment 471100
Later, it will get glued in place...handle blank...
Attachment 471101
Needs a cut made, mainly to get rid of that knot..
Attachment 471102
Will sand things smooth, later...had Mortise and tenon work to do..
Attachment 471103
Once the tenons were cut, I could put the scrollsaw away...and free up the bench...dry fit #1..
Attachment 471104
Then the other end...and finally, just went ahead and glued things up...didn't even bother to sweep up, just took the camera back upstairs, and called and end to the fighting going on....even the shop stool was always trying to trip me up....that was quite enough "fun" for today.....always tomorrow,eh...
Stay tuned...
-
Well...glue-up had sat about long enough...might try in a little bit...say about 3:00 pm? need to get the bottom panel glued in place...and figure out how to fit this into the box..so that it won't rattle around...
Stay tuned...cussing MIGHT be required?