Oneway Chuck Spur

Printable View

10-16-2018, 8:59 PM
MICHAEL YASKO

Oneway Chuck Spur

Hello, Does anyone know if the Oneway 1" Chuck Spur will only fit in a Oneway chuck or would it work with a Vicmarc 120 chuck? It would seem like it should but hey that's why I'm asking. Hopefully someone would know. Thanks for your help.
Please ignore this post It's the 1/2" spur drive I'm looking for and not a 1" drive. I want to start off-axis turning and I need a smaller spur drive when using a smaller spindle size. i"ve looked everywhere and I can't find one. Anyone have a 1/2" spur drive they'd like to sell?
10-17-2018, 1:29 AM
Leo Van Der Loo

Michael I have the ½” spur drive from thee Taig lathe, (no I don’t want to sell mine, as I occasionally do use it’

Lee Valley sells it, but you might be able to get from a Taig lathe seller closer by.

http://www.leevalley.com/en/Wood/pag...330,50260&ap=1
10-17-2018, 7:37 AM
Prashun Patel

I have the oneway chuck spur and the Big Bite. They both fit in my supernova chucks fine. Not sure if that means they are compatible with all chucks.
10-17-2018, 8:15 AM
John K Jordan

1 Attachment(s)

Quote:

Originally Posted by MICHAEL YASKO

It's the 1/2" spur drive I'm looking for and not a 1" drive. I want to start off-axis turning and I need a smaller spur drive when using a smaller spindle size. i"ve looked everywhere and I can't find one. Anyone have a 1/2" spur drive they'd like to sell?

Our friend Brian Horais, who turns and teaches off-axis turning, recommends a 5/8" 4-prong drive center. Hurricane has one:
https://www.amazon.com/Hurricane-Tur.../dp/B079HJCCRX

PSI sells a 5/8" 2-prong but I think I'd prefer the 4-prong.

I see some offer a 3/8" spur center that might be good for very small work.

I have the 4-prong centers but for a bunch of years I've been doing most of my spindle turning, off-axis or on, with a #2MT Sorby 1/2" Steb drive center. It doesn't hold as well as the 4-prong but no catches, no problem. For the tailstock end, I almost always use a 1/2" Steb live center. These are not cheap but I won't leave home without them. :)

https://www.woodturnerscatalog.com/p...n-Drive-Center

https://www.woodturnerscatalog.com/p...volving-Center

Attachment 394981

JKJ
10-17-2018, 8:42 AM
MICHAEL YASKO

Thanks Leo Van Der Loo, I checked that out and probably the only 1/2" one I'll find, was hoping for a MT rather than a collet. I have a 3/8" but mayne have to settle for the 5/8" since it's widely available.
10-17-2018, 8:45 AM
MICHAEL YASKO

I have a supernova chuck as well but I meant the 1/2" and not 1" . Thanks though, that's good to know.
10-17-2018, 8:49 AM
MICHAEL YASKO

Hi John, I have a 3/8" but looks like I may have to settle for the 5/8". I prefer the 4 prong as well. The 1/2" was the one Barbra Dill uses and recommends but she said they no longer make it, can't remember which brand it was.
10-17-2018, 8:55 AM
John K Jordan

Quote:

Originally Posted by MICHAEL YASKO

Hi John, I have a 3/8" but looks like I may have to settle for the 5/8". I prefer the 4 prong as well. The 1/2" was the one Barbra Dill uses and recommends but she said they no longer make it, can't remember which brand it was.

Looking at the 5/8" one I have, I don't think it would take much effort to grind the tip down to 1/2": turn at low speed in the lathe and use a grinding wheel in a Dremel.

JKJ
10-19-2018, 2:13 PM
MICHAEL YASKO

Quote:

Originally Posted by John K Jordan

Looking at the 5/8" one I have, I don't think it would take much effort to grind the tip down to 1/2": turn at low speed in the lathe and use a grinding wheel in a Dremel.

JKJ

Thats a good idea John but I found one finally on Packards site. They have 3/8, 1/2, and 5/8 under there there Mini 4 prong drive centers. I don't know how I missed that before. All is well now.