Use for a plank?

Taking a little vacation after the last project. Had a "Must-do-by.." project next week...once other items arrive...have to build a box for them to nest in. Will have 1 week to get that done, and shipped on to the next person in the chain....( may even show a few photos, when done?)

Once that is done....there is still some "leftovers" of Ash in the shop. There is also a 4/4 x 6 x 8-1/2' plank to bring down to the shop...might see IF I can make a small, Shaker Style table, with drawer, out of just those "parts" ( secondary wood will be either Poplar, or Pine), including the legs...

Sound doable? Maybe a 15" x 15" top? Plank is 6" wide, but very rough on the edges. Did not see any knots, this time...never know.

Stay tuned....this might be fun...

Hi Steven,

I don't know, if you have enough of the "leftovers" ash scraps, I think you get it done. I don't think it will take much in the way of the leftovers, but I am thinking that the one plank may be just a bit short by itself. However, I have great confidence that you will figure out something good!

Stew

Might be a week or two.....BP issues....217/107...before the EMS squad hauled me away to the hospital Friday evening....got back home Saturday evening, still not feeling too good...

Think I sit back and rest up a while....

Hi Steven,

Take some time to rest and wait till things settle down a little and you are caught up on your rest. Thanksgiving day is coming!

I appreciate your posts and thank you for doing the projects.

Thanks and regards,

Stew

About noonish this coming Wednesday, a visit to the Cardio Doctor, to find out what he found out, and what he wants to do....right now, I have trouble with stairs....at lease in going up a set....

Have a saw to pick up, and two Rip saws to drop off...might do that after the visit...Sharpening Service doesn't open until 2pm, anyway.

About fifteen years ago, a friend had a heart attack. They inserted a stent.

Now he sees the heart doctor twice a year. He read a book on fitness walking and walks every morning.

Google "fitness walking".

Ex-leg Infantry....walking isn't much of a problem.

Second spell, last night...244/125.....they redid the BP meds.....they seem to think my current ones were getting out-dated....haven't been changed in over 5-8 years...130/70 when I got out this afternoon....I'm plumb tuckered out.

Backed out of the nesting box commission....take a bit of time off. May pick up a couple boards this week...have a sharpened saw to pick up, and 2 to drop off.
Will update after tomorrow's Cadio Check up....

Well..wasn't that great of a day.....Sharpening Service was closed til Friday ( Mon, Tue, Fri, 2-6pm)

cardio Doctor visit....am now scheduled for a Heart Cath the first week of December....and a couple other meds to try.....they will be going up through the groin, instead of Radial through the wrist...might be a while before I am allowed back into the shop....

Have no real restrictions until the Cath date....decided to keep things simple in the shop....do one task a day....with a one hour time limit...no more 4-6 hour marathons....

task yesterday? Plank was slowly hauled to the shop. Placed in the end vise on the bench....
Attachment 419974
Marked out 18" per cross cut....and used this D-8, 11 ppi, 26" long saw to make 3 cross cuts. took a short break...
Attachment 419975
Rather than hand saw for width, or plane the edges to joint them...I set up the rip fence 3 times....once to remove the worst of the wavy edge, second to "joint" the almost straight edge, and then once more to "joint" the first edge...then clamped the 3 blanks together....
Attachment 419976
And let them sit a day or two....end grain?
Attachment 419977
And the face grain?
Attachment 419978
I dug out the scraps from the DVD Cabinet build..
Attachment 419979
Can use these 2 as blanks for some of the aprons.

task for later today? Reset the fence on the tablesaw, the 3 blanks for the top are just over 4/4" thick, would like them to be 3/4" thick. Set the fence to buzz the worst off...saw blade isn't quite big enough...so...
Attachment 419980
After the tablesaw goes all the way around, this can clip off the ridge in the middle, then maybe a bit of handplane work, then the final run-through to get to finished thickness....then maybe a glue up? Going to rest up a bit...might head to the shop later today.

Stay tuned....

Shoptime...Begin @ 1500hrs....end @ 1615 hrs....15 minutes overtime. Set up the saw's fence...
Attachment 419993
Even with the blade all the way up....
Attachment 419994
Can't reach the center of a 5-1/2" wide board....tried the bandsaw, to remove what was left...
Attachment 419995
Did not go well...tried to clean up with a couple planes...
Attachment 419996
More work than I need to be doing....reset the saw a few times...ripped the 3 blanks, right at the top of the saw blade cuts....then set the fence, and ran all 9 blanks through on edge, to get to 3/4" thick...then clamped the stack together...and called it a day..
Attachment 419997
Tomorrow, maybe, I'll lay these out flat, sort through for the best looking pattern of the grain....might even glue it up into a panel?
Stay tuned...

Kind of slow, today?

Cleared a flat space...
Attachment 420076
Biggest flat area in the shop....slap a plywood panel down..and do a 1st sorting..
Attachment 420077
Not quite right...do a second sorting....
Attachment 420078
Meh, a little better....rotate the mess...
Attachment 420079
Then rotate the parts for a bead of glue..
Attachment 420080
Spread the bead a bit, mooshing the part around until it "sticks"...then add a few clamps & cauls...
Attachment 420081
And let it, and me sit a day....maybe 1/2 an hour's work?

May try to lay out blanks for the legs, tomorrow...
Stay tuned...

For my One Hour of Shop Time today....Removed a few clamps..
Attachment 420158
So I could clear off the tablesaw...and make a mess...
Attachment 420159
Ripped two planks to 2" width...lots of wavy edges, and faces....by the time I was done....had 6 blanks at 3/4" x 1-5/8" x 20"...

Then matching the grain patterns between each pair of blanks...spread some glue, and clamp them up....
Attachment 420160
Had enough to make 3 out of the four legs....had to use the vise..
Attachment 420161
To keep things from slipping around....I intend to taper two sides of the legs....leaving the best looking faces alone...

Looks like I need to "Road Trip" and buy a stick or two of Ash....
Stay tuned...:D

Well...hauled a 1 x 6 x 5' Ash plank to the shop. Atkins No.65 to cross cut twice. Then, since both my rip saws are out to be sharpened...tablesaw came next. Ripped a few strips.

Glued up the better of the bunch,
Attachment 420357
So that leg #4 is getting done. Two other strips..
Attachment 420358
Needed trimmed for length, to make blanks for the bread board ends...
Attachment 420359
And stashed them both here...and still had enough to get some apron stock...
Attachment 420360
Figure I can cut the best out of these three...may even see about a drawer?
Other three legs are out of the clamps..
Attachment 420361
And was able to square both ends..
Attachment 420362
Need to clean the glue joints up, and start on tapering 2 sides of each leg....
Attachment 420363
may have used a tad too much glue?

Stay tuned...

Today was Turkey Day, due to everyone's work schedules....sitting here stuffed at the moment...doubt if the shop will open, today.....maybe tomorrow. Need a nap, right now.

Next Tuesday is the Heart Cath.....up in Lima, OH. Then I have to be a good boy, until the plug heals...

Stay tuned...

Quote:

---

Originally Posted by steven c newman

Might be a week or two.....BP issues....217/107...before the EMS squad hauled me away to the hospital Friday evening....got back home Saturday evening, still not feeling too good...

Think I sit back and rest up a while....

---

Dang. Are you doing better? That's dangerously high BP.

Hey Steven,

Take a good portion of tomorrow off also. Left over turkey, potatoes and gravy, football on TV.

Stew

Lets see...been busy today, trying to wind down from it.....almost 3 hours IN the shop, today....trying to work that extra weight off..

Legs for the table...have been cleaned up, squared up, tapered 2 sides...round-over-ed on one outside corner...
Attachment 420507
Attachment 420508
Bandsaw to rough in the tapers, then these two tools to smooth the tapers..
Attachment 420509
Set aside until needed, again....flattened the table's top...
Attachment 420510
From this to..
Attachment 420511
Then the #78..
Attachment 420512
Twice on this end...to fit..
Attachment 420513
One of the bread board ends...may try to do the other end tomorrow....after all the running around is done.
Stay tuned...

Ok...worked about 1 hour this morning.....Clamps came off the top.....planed and sanded both faces smooth...decided this face will be the "underside"
Attachment 420568
Then laid out where the legs will go....1" overhang, all the way around. Then started cutting apron blanks...
Attachment 420570
Cut one end square, allowing for 1/2" long tenons on each end....cut a blank to length..
Attachment 420571
And soon had all for blanks cut...
Attachment 420572
Then lay out and cut the tenons....
Attachment 420573
Hour was done. DEpending on how a football game turns out....I may head back to the shop..have mortises to chop
Stay tuned :D

Ok...lay out a few toys..
Attachment 420663
Lay out where the mortises will go...have 8 to do..
Attachment 420664
Chop a while, test the fit...
Attachment 420665
Chop a bit deeper..
Attachment 420666
Had a few "crumbs" down in the hole, shook those out. Rinse & Repeat...then a dry fit..
Attachment 420668
No glue, yet. Need to make 4 corner blocks, first. Spent most of the 2 hours today sitting down..
Attachment 420669
Had two squares set up, to do the layout work..
Attachment 420670
And used the tenon to locate where the mortise needed to be.

Decided to hang up the apron...
Attachment 420671
And call it a day...at least until after Supper...maybe..
Stay tuned....Have to get things done, before Tuesday morning...

Hi Steven, sorry to hear about your recent medical issues. I hope you are feeling better.

Ripped some pine scrap down to 1 x 2s
Attachment 420755
Then used a mitersaw to make a few cuts..
.Attachment 420756
until I had 4 corner blocks....
Attachment 420757
Then a few pilot holes and countersinks
Attachment 420758
Aprons were planed smooth on the show side, and a slight round-over on the bottom edge.
Then a glue up of all the parts....and quite a bit of cussing...
Attachment 420759
Clamps sat a day, then, drilled slotted holes in each corner block. Round-over bit was run around the edges of the top...
Attachment 420760
Good side down, used a combo square to center the base..
Attachment 420761
Added washers to each screw, and attached the base to the top..
Attachment 420762
And set things aside for a bit...and a PIP

Stay tuned, BRB..

Time to show off a bit...
Attachment 420763
Before the "Gunstock" stain goes on....
Attachment 420764
And, after the stain was brushed on...and wiped down..
Attachment 420765
Just a simple, little table....
Attachment 420766
Waiting on the stain to dry, before a top coat...

Stay tuned, almost done....

Just got back home this morning...Heart Cath went OK....no stents needed. So. now I am on the "DL" for a few weeks, letting the plug in the leg's artery heal up.

Maybe the first of the year, before the next project starts...

Good to hear you needed no stents and will be ready to go in a few weeks.

No stents were needed. Everything looked good, I guess. They seemed to think it may be a kidney causing the troubles.

Table has been hauled upstairs ( Grandson) and a quart of Amber Shellac has been brought upstairs....just need a place to brush on the finish...3-4 coats....and see how it looks.

Rearend is getting sore from all this sitting around....might give it a break, by using the brush.

1st coat is on the table.....may get #2 after a bit..
Attachment 421061

Will take a few more coats....

3 coats are done, and have been rubbed down.
Attachment 421203
Attachment 421204
Attachment 421205
Think I can call this little table done.