I am looking to buy a cordless impact
18 volt would be preferred
any experienced recommendations are welcomed
thanks
Printable View
I am looking to buy a cordless impact
18 volt would be preferred
any experienced recommendations are welcomed
thanks
My families farm has used and severely abused Dewalt impacts for years and have had really good luck with them. We have burned a few motors out but they were getting heavy use in a grain bin for over half a day. I have not personally owned a milwaukee impact but their tools are also very highly recommended (we have a few of their battery grease guns around). Dewalt sells two different impact models. We use both on our farm depending on the job we are doing there is significant torque and weight differences between the two. I posted a link from northern tools for the larger impact.
http://www.northerntool.com/shop/too...xz0aAtyS8P8HAQ
I vote for Bosch or Makita.
I have a Makita that has given me nothing short of great service!
I have the smaller DeWalt 18V and it's given good service but I haven't used it as much as Ethan.
Mike
I recently went with the Bosch. Haven't used it enough to comment on it yet. I got the combo set from Lowes with the impact driver & drill for about $200 minus 10% for my military discount.
The whole Milwaukee M18 line is great. I do currently have a problem with my hammer drill but I've hot a number of the tools and really like them. Get the Fuel version of the impact which has more finesse.
I'm not sure about the above suggestions but I will tell you the Ridgid one I have is absolutely awesome. I got it in a kit with a reg cord drill and the radio (never thought I'd use the radio but actually do). When I go mine I also register each item and each battery (3) for lifetime replacement. Not sure how to beat this deal.
Are you looking for an impact driver or an impact wrench? I ask because you didn't specify, and both can be cordless.
I am a big fan of the Milwaukee M12 and M18 Fuel tools. The M18 Fuel impact has more then enough power to handle about anything you can throw at it. I never use my air impact anymore, since getting the Milwaukee, as I haven't run into anything the Fuel wont handle. The battery's last forever and recharge quickly. It also has a 5 year warranty. http://www.milwaukeetool.com/power-t...rdless/2763-22
Yeah, I had a flat and it was impossible to get the lug nuts off with the tool that came with the car. I don't know if the tire company puts the lug nuts on super tight or age and corrosion locks them on, but they were TIGHT. Impossible to get off except with an impact tool.
Mike
Impact driver
my Makita 18v NiMH cordless drills for over for over ten (14)years looking at replacement batteries and wonder about going impact
the guys at work use them
I think they are slower than my makita, but more precise at stopping at your preferred depth...
I have the Milwaukee and have been very pleased. You may consider a drill and driver kit. Sometimes they are the same price as the driver only with charger and batteries.
Since you want a impact driver then this is what you should check out. http://www.milwaukeetool.com/power-t...less/2653-22ct You should also check out the M12 Fuel Impact driver as it is smaller and has enough power for most jobs. http://www.milwaukeetool.com/power-t...rdless/2453-22
I helped a lady once with a tire change at her house. I thought I was going to break my 4-way (or part of me--I'm fairly strong and stubborn), so I went to get my compressor and impact wrench. Even with the impact wrench at full power (rated 500 ft-lbs), and the pressure set beyond the recommended, I still had to sit on a couple of the lug nuts for a couple MINUTES with the impact wrench before they finally broke loose.
I got the Bosch 18V impact driver and drill set about 6 months ago. Every time I use it I kick myself for not getting it sooner.
Go Brushless, either Milwaukee Fuel (M18 or M12), DeWalt XR 20Max, or Bosch EC. I have a Bosh 12v Impact driver, and have just recently acquired the DeWalt XR 20Max. The XR is an absolute beast of power, but light and handy, and by all accounts the Milwaukee M18 Fuel is as well. I got the XR because my Bosch 12v wasn't up to some of the jobs I called upon it to do, the XR has easily handled everything thus far I've thrown at it.
The Brushless motored tools are more expensive than the comparable brushed motors, but they ARE more powerful for the same voltage, and will run significantly longer on a charge.
One comment not mentioned so far is the ergonomics of the tool. I've had and used Dewalt impacts and have and use both Milwaukee and Makita models. The Makita is the most comfortable to use with its smaller handle. I've been using it since Makita introduced their Lithium Ion tools still grab their brushless tool whenever it's available. Having said that, the Milwaukee has the most power and runtime if that is a higher priority, but I've never really found that I've needed more of either when using my impacts. I do carry the Milwaukee M12 Fuel in my tool bag and find it will generally handle most jobs. It is a nice compact tool, but still has a larger handle that that on the Makita 18V.
I would stick with the industrial brands though. I've known several people who've gotten some of the cheaper brands of cordless impacts out there. They work well initially, but generally the batteries head south much sooner than that in your quality tools.
Regardless of what you get, I'm sure you'll be happy with the new acquisition.
Clint
You state you want an 18v., have you looked or use one of the new 12v. drivers?
I have the Milwaukee M12 and love the little thing, it will drive lag screws into 4x4 like mad, now I am sure it will not be as powerful as an 18v. but the size is sure nice.
I can agree with this almost word for word. We also have several milwaukee tools here though, and the dewalts have proven to be a lot tougher under pretty heavy use. Pretty tough to beat the old reliable 18 volt dewalt, although the "prettier" tools can be enticing, I stick with what works. Killed a dewalt once when I dropped it off the roof of the house, from about 20 feet, on concrete.
I have both the M18 and M12 regular and fuels, the advantage of the fuels is they have 2 settings on the M12 and 3 on the M18. This is the feature I really like plus they run forever on a charge. The M18 fuel although heavier is more compact than the M12 fuel. I keep the old M12 in my car for those dumpster find dissemble needs. HD was running a free 4 Amp Hour battery with the purchase of the fuel kit. Dan
I'm a big fan of Bosch. Their 12v system will do 98% of what a woodworker will need. If you want 18v check out their new "Socket Ready" tools.
I have been happy with my Makita 18v brushless impact driver. Once you have owned an impact driver, you will never want to run large screws any other way. Small screws sometimes warrant the more precise touch of a drill or by hand. Get one that has several power modes so you are not trying to drive a 5/8" #6 screw with the same power as a 4" #14.
I have been using my Makita a ton the past two months. Love it. LXT 18V Makita with 3.0ah batteries. Also use my 12V Bosch impact a ton and the 12V screw guns.
If I was buying today I'd probably buy a 20V Dewalt vs the Makita.
The MILWAUKEE Fuels - excellent tools and good customer service. They have an online system for sending in tools for repair that is faster and cheaper than going through a local service shop. I use my 18v fuels every day and they are the best I have owned, even better than my 6 year stint with Panasonics.
Sorry I wrote Bosch in the 1st edition - I had a flat spot this morning :confused:
I think this thread illustrates that they relatively new category of impact driver is fantastic, and we all really like the ones we have.
I can't say I've had any trouble running small screws with my 18V impact. You just have to have a light touch on the trigger and watch the screw. I will say that I was used to holding a drill/driver loosely so that when a screw was tight, my loose grip would allow the driver to swing instead of over-torquing the screw. I never found any use for the torque setting clutches--driving screws into wood results in too wide a variety of torques.
When looking for a tool to buy I look at what the Pros, that use the tool all day long every day, are using. Sheet metal workers drive in screws and bolts all day long and most use Makita impact drivers for the past 15 years that I know of. I still have some Makitas I bought when I retired in 2000.
I have the 18v Lithium combo set by PC and really like it. Batteries are kind of small, but nice and light. My son got me a full size Lithium battery pack for my birthday which is better for larger projects, like a deck.
Just my 2 cents here. I have used two different impact drivers. I own a "little" Hitachi, and my son has a Makita, both 18V Lion. I'm sorry but I don't know the specific model numbers. Anyway, I love my Hitachi and use it frequently in my woodworking. It seems a little light to be driving a lot of . . . say . . . 3" deck screws or some longish screws into very hard woods, but it does it. And the battery seems to last FOREVER.
One day I was at my son's place doing a little woodworking and used his Makita. It seemed to have a lot more power and I had to be much more careful when driving screws so as not to strip them, screw them way down into the wood, or even break the screws. But if I was driving those long 3" screws the Makita would be a clear choice.
When my son bought me my Hitachi as a present I wondered what the heck was going through his brain. I would never use the *&^%%$& thing. But I tried it and liked it and now I would say that an impact driver is getting very close to being a must-have tool. It will do a lot besides driving screws, but there are also some things that it doesn't do well. Driving small screws like #4's and #6's, and drilling into steel comes to mind.
So from MY experience, I would say get one. But try to get one with power to match what you intend to do with it.
Wayne
Anyone familiar with the Panasonic?
Panasonic makes some great tools, and probably the best batteries in the cordless segment. This is in part because they are, to my knowledge, the only cordless tool maker that makes their own batteries. Their tools have always been highly rated, but have more limited distribution than the Big 4 (Makita, DeWalt, Bosch, Milwaukee), generally cost a bit more, and are not updated as frequently.
I resisted getting a cordless impact tool for quite some time.
I recently bought the Dewalt DCF895D2. Very nice tool but pricey.
Brushless are a newer development, but you get a lot more battery life. Wouldn't buy one without it based upon the battery life. It's like getting twice the capacity battery.
I used Pansaonics exclusively and very happily for 6 to 8 years but had to give up on them after I could no longer (find to) purchase a drill or a driver with 2 batteries in a kit.They started packaging everything so that you needed to buy extra tools in order to get a 2nd battery - a real deal breaker for me. Bad marketing !!! I bought the Milwaukee M18 Fuel instead. Very happy.
I have a medium sized construction business, building wineries. We have tried a number of brands and tools. We have found the Milwaukee M-18 line of tools to consistently give us the best service, always performing without fail.
The other brands just don't hold up to the demands of getting the job done on time.
I went Milwaukee 18V hammerdrill and impact driver
got the light too
I am Happy
I just bought the 7 1/4 fuel saw
awesome!
"carpe lingum" -- thanks for the laugh
I've built countless projects and two houses with a deWalt 18-volt impact driver. I also use it all the time with an adaptor with my socket set to do mechanical kinds of work. If you haven't used one before, you are going to be very very impressed: first thing I did with mine was drive a 6" lag bolt through a 4x4 and back again, no pilot hole, no hesitation. Mind you, the bolt was burning hot by the time it came out!
I imagine you will be happy with any quality brand.