-
5 Attachment(s)
Both ends were done first, going across the grain...a "stop line" was marked along the center of the edge, and about a 1/4" or so down the face...Tools?
Attachment 518379
Spokeshave where the grain allowed...otherwise it was just the No.3...Got both ends done, on both faces..
Attachment 518380
Then hand sanded with 80 and 220 grit sandpaper....then the long grain edges were done..
Attachment 518381
Trying to keep that sharp corner....
Once all four edges were Thumbnailed...time for the glue bottle..
Attachment 518382
Used a caul across the front...and..
Attachment 518383
3 clamps around in back.
Will let this mess sit a day...while I figure out the building of a Drawer....and. whether to use through dovetails for it...we'll see...
Stay tuned..
-
4 Attachment(s)
Got the lid to size
Attachment 518454
4 parts for a Drawer..
Attachment 518455
Milled a place for the drawer to house a plywood...
Attachment 518457
Dovetails as well..
Attachment 518458
-
5 Attachment(s)
Keyboard issues this morning...had to go and replace it. Seems a cat had walked across the computer desk, and knocked over my glass of Tonic & Gin...right onto the keyboard.
Monday....gotta love it...not. The way things are going this morning, I think I might just leave the Shop closed for today..
As for that plane?
Attachment 518467
Craftsman No. 3720..aka..Sargent No. 79, Type 2......that Mr. Brown was kind enough to nickel plate up like new...
Attachment 518468
Dovetail layouts, as I had to work around that rebate...
Attachment 518469
Back 2 corners are done...need to find out the width/depth and cut the plywood to size...length is fine..
Attachment 518470
The #3720 does make a mess on the shop floor...had to sweep up the floor when I was done...
Attachment 518471
Lid and all 4 drawer parts...will see how today goes along....and how bored I get...
-
This case can then sit on a shelf..until a Project comes along that needs chisels...then it can sit down on the end of the bench, where I can access the sizes I need that day...when not in use, back onto the shelf.
Thinking I'm going to do Half Blind Dovetails for the front...we'll see how the Brain works, today...
-
7 Attachment(s)
Half blind dovetails for the front of the drawer...meant I needed to cut existing pins back about 1/8" from where the others were...instead of 1/2" long pins...they needed to be 3/8" long..
I still lay the pins out at 1/2" long, though...
Attachment 518489
Then cut them for final length..then used those pins to do the layout for the tails..
Attachment 518490
Just traced around. Dovetail saw to cut inside the waste side of those lines..just nicking the base lines. then the chopping began..
Attachment 518491
Some with a normal chisel, and some with...
Attachment 518492
One that was reground into a triangular shape, to get into the corners better..
Got both front corners done, and tried a dry fit...
Attachment 518493
And this is what you will see when the drawer is closed...a panel was cut to size, and dry fitted..
Attachment 518494
Was about the right length, just a hair too wide...plane skimmed enough off for a nice snug fit....then the clamps and glue arrived..
Attachment 518495
So....later today, I'll remove these clamps, clean things up...might see about a wood knob. Then work on that lid..
Stay tuned..
-
7 Attachment(s)
Ok...those clamps came off this morning...back was cleaned up..
Attachment 518514
Followed by both ends, and then the front..
Attachment 518515
And the top edges leveled...then the bottom was leveled...
Attachment 518516
As some of the rebate edges were a hair proud of the panel
Was able to do a test fit..
Attachment 518517
But, until a knob was installed, didn't feel like push it all the way in...
A support was added to the inside of the drawer...
Attachment 518518
Then laid out the diagonals, to find the center of the drawer front..
Attachment 518519
A cordless drill was used. A Mini Shaker Peg was modified to fit....
And NOW I can push the drawer in as far as it can go...
Attachment 518520
Maybe tomorrow, I can work on that lid a bit?
Stay tuned..
-
6 Attachment(s)
Lid needs a rebate, like this older case has..
Attachment 518597
Which gives the hinges a bit more room, and the rebate acts as a stop when the lid is opened..so..
Attachment 518598
Ends were a bit deeper than the front and back edges..used the case to mark out where the rebates went..then start on the ends..
Attachment 518599
working on end grain, with a Stanley No. 3, Type 11...trying NOT to nick the rebate's walls..then do the "top" edges..
Attachment 518600
And smoothed out with 220 grit...then, with both ends done, repeat for the long grain edges..
Attachment 518601
Was trying to keep a "crisp" corner...
Attachment 518602
All sanded to 220 grit..am now about ready to make some feet for the case to sit on...
Stay tuned..
-
I’m just catching up on this thread. The chisel box looks like it is coming along nicely, but I have a more important question: Do you often have a gin and tonic in the mornings?
If so, I have something to look forward to when I retire!
-
Sorry..Dry Shop...I save the booze for when I am done for the day....sometimes a Guinness,,sometimes the Tonic & Gin.....now and then maybe a shot of good Irish Whiskey?
-
8 Attachment(s)
Was working on feet for the case to sit on...Miter saw cuts..
Attachment 518672
Were having an issue...when a part is 1/4" x 1/4" square...and the back corner that meets the fence on a folding Mitrebox...
Attachment 518673
Has a round-over..small parts can ( and did) roll backwards a bit, into the gap...not an issue with 90 degree cuts...but with a 45 degree sort of cut, it becomes angled...decided to put the GEM away, and continue with the bandsaw..
Attachment 518674
Will sort through this mess, tomorrow...to find the best 4 to glue up as feet for under the case...always nice to have a few spares handy...
Hinges:
Attachment 518675
Had a "flaw" at least for me...so...this was used to correct that flaw..
Attachment 518676
And the flaw?
Attachment 518677
Note the gap back by the barrel? We have ways...
Attachment 518678
Pinch it in the Monarch Vise, once per side..hammer adjust for any bends going on...
Need to do a bit of layout work, before these tools can do their thing..
Attachment 518679
Stay tuned...
-
Layout work...the barrel of the hinge, sits in the rebate under the lid..
Attachment 518680
I set the hinge at the corner of the rebate, make a mark on the other end of the hinge,,,the lay out the hinge locations..
I needed a way to keep the lid ( and the case) from hopping around on the bench, while I worked to install the hinges...so...
Attachment 518681
For the lid. a 6" clamp will do ( case needed 12" clamps) one on each end...
Attachment 518682
Only had to remove the thickness of the hinge's leaves...Wide chisel along the back..1/2" chisel to chop the waste..3 hits, move, 3 hits, move..before the last hits, turn the chisel so that the flat back faces away from the waste...then pare away the waste...wide chisel to flatten things a bit. Eggbeater drill, with a 1/16" bit, for the pilot holes. Phillips screwdriver to drive the tiny screws that came with the hinges (and clock them..)
Repeat for the other end..
Attachment 518683
Then use these hinges, to lay out the locations on the case..
Attachment 518684
And chop and drill...Then the "FUN" part...Holding the lid in place, while trying to install a screw, with a screwdriver...with just 2 hands..and one of them shakes a lot..once THAT one screw is in...the rest follow easy enough..
Attachment 518685
Then try to close the lid....found a high spot on the back left corner of the case...lowered that down a bit..
Attachment 518686
I don't have a way to "latch it" closed..yet...so..
Attachment 518687
I think that will do the trick, for now..
As to how many chisels?
Stay tuned..
-
This is getting very OLD! To correct this? Either the Mods FIX the site...or...I have to go back and re-load EACH of those photos...seems to happen about once a month..there is NOTHING changed on MY end of things....same picture size, same loading actions...they even show up when I go to edit the post...as soon as I hit "save" these stupid blue "Attachment 123456" blurbs take the place of the photo...and...when I click on those..it tells me this is invalid? WTF!
IF you people want to see thiose photos in the last post..talk to a Mod....
I will try to post ONE more time, to see IF the Photo BS has been fixed....
-
2 Attachment(s)
Shoptime today? feet installed....fancy feet, at that..
Attachment 518732
With glue and very small nails..
Attachment 518733
Letting this sit overnight...
Stay tuned..
-
Laundry Detail. this morning...so..despite it being a Monday....the feet have been leveled...need to unload the washer after a bit...and the Chisel Case...and see about a finish of some sort..
Dungeon Wood Shop Spring Cleaning is also underway...amazing what one finds underneath the piles of junk....
Stay tuned..
-
A coat of Witch's Brew was mixed first....old stuff was a bit too red...dumped what was left of the Special Walnut into the can..and gave it a good stir..
Coat has been brushed on..and I am allowing it to dry...before the next step....
have to go and unload the Clothes Dryer after bit...will see how things are doing...maybe a rub-down with 0000 steel wool? We'll see...
Photos? When this site gets it's act together, I MIGHT post a few....