New Woodworking Bench (Parts I & II of II)
Way back in Sept '07 after completing new extension and outfeed tables for my tablesaw, I said that my next project was going to be a relatively traditional woodworking bench based on a design by Lon Schleining which was first published in FWW a few years ago (see the copy on my extension table) . However there was always something with higher priority, and I never got around to it.
http://www.ncwoodworker.net/pp/data/...m/P5220039.JPG
Then, last December, while working on my second adjustable height assembly table (for a magazine article), I wondered if the adjustable legs I designed and built for those tables could be adapted to a woodworking bench such that the bench would be strong and stable.
I broached the subject to some friends and posted a few SketchUp drawings of the leg design. However the location of the stretchers on the initial design would likely have make it difficult or impossible to lift the top to adjust the bench height.
http://www.ncwoodworker.net/pp/data/...Bench-down.jpg
I subsequently changed the location of the stretchers from the fixed legs to the adjustable legs.
Since I already had an indexing jig set up to cut the leg notches for the assembly table legs, I decided to make the woodworking bench legs at the same time, using some beech I had sitting around the shop- that was over 9 months ago. This Spring I picked up a 30" x 72" x 2.75" maple top and some pieces for the aprons from Bally Block, then on a trip to Raleigh last month I picked up a few more pieces of beech for the base and more maple for the vise jaws at Klingspor. So finally, almost two years after having made the decision and over 9 months after actually cutting the first pieces, I had all the materials (and made the time) to actually start working on the new bench. I didn't take any in-progress shots, but here are some pics of the nearly completed adjustable height trestle base with top installed. I still need to add the maple aprons, 3 vises (QR front vise, sliding tail vise, Veritas twin screw tail vise), and bench dog holes.
Revised SketchUp drawing. (minus ratchet arms and release cords). Unlike my assembly table legs which stay together by sliding dovetails, these legs mate with a "V" and "V groove". The ratchet arms draw the leg halves together and keep the matching "V" profiles solidly mated.
http://www.ncwoodworker.net/pp/data/...edium/AWWB.jpg
The unfinished top is just resting on the trestle base which is in its lowest (30") position. It is adjustable in 1" increments.
http://www.ncwoodworker.net/pp/data/...m/IMG_2822.jpg
End view showing top and bottom draw bored tenon pins on legs and wedged through tenons on stretchers.
http://www.ncwoodworker.net/pp/data/...m/IMG_2829.jpg
Close-up shot of ratchet pawl arms (minus release cable) and stretcher tenons.
http://www.ncwoodworker.net/pp/data/...m/IMG_2825.jpg
End view, one notch below full height (43").
http://www.ncwoodworker.net/pp/data/...m/IMG_2830.jpg
The adjustable height mechanism works very, very well (as good or better than the ones on my assembly tables). The bench is very sturdy, stable, and does not rack. While heavy, it lifts fairly easily -obviously one end at a time.
Before I continue, here are some stats-
Design:
- A mix of elements from Lon Schleining's "The Best of Old and New" bench from his book and Fine Woodworking article. Elements include his thumbnail profiles on the feet and jaw faces, etc. and my own designs including the adjustable height trestle base. The adjustable trestle base is a new twist on my assembly table adjustable height legs which will be the subject of a forthcoming article in Dec/Jan issue of American Woodworker.
Materials:
- Top, aprons, vise jaws- hard Maple
- * Adjustable trestle base- American Beech.
Construction:
- Trestle base- mortise & tenon and Titebond III
- A mix of pinned-blind and wedged-through M&T joints
- Aprons (and sliding tail vise) joined with hand-cut, half-blind dovetails - 6 sets!
- Long side aprons attached to the top with glue only (long grain to long grain)
- End aprons, to allow for seasonal changes in the cross-grain direction, are held in place with threaded rod, nuts, and barrel nuts. No through bolts or plugs are visible on the end vise face or free end aprons of the bench. Nuts are accessible from underneath to allow tightening.
Dimensions:
- Top: (not incl. vises): 33-1/2" wide x 74" long x 2-1/2" thick- Yes, it is BIG!
- Aprons: 1-3/4" thick x 5" high
- Height: adjustable: 30-1/2" to 43-1/2"
- Weight: TBD, but HEAVY!!!
Vises:
- Lee Valley twin screw full width tail vise (20" between lead screws) (3" thick jaw)
- Quick release front vise (3" thick jaw)
- Sliding tail vise (w/o shoulder)
(all vise hardware was free, courtesy of the Woodcraft Top Shop contest gift certificate )
Aprons and vises installed:
http://www.ncwoodworker.net/pp/data/...m/IMG_2867.jpg
http://www.ncwoodworker.net/pp/data/...m/IMG_2870.jpg
On one end is a Lee Valley/Veritas Twin Screw, full width, tail vise. It was a custom installation. Rather than surface mount the vise and add the chain housing to the back of the 3" thick vise jaw like the typical installation in the first picture below, I routed a recess for the flanges, sprockets, and chain and made a new, low profile cover.
http://toolmonger.com/wp-content/upl...nscrewvise.jpg
http://www.ncwoodworker.net/pp/data/.../IMG_28641.jpg
http://www.ncwoodworker.net/pp/data/.../IMG_28652.jpg
http://www.ncwoodworker.net/pp/data/...m/IMG_2874.jpg
http://www.ncwoodworker.net/pp/data/...m/IMG_2875.jpg
Part II below
New Woodworking Bench (Part II of II)
One detail I haven't shown was how I attached the cross-grain aprons to the bench. Since they are cross grain you can't use glue without the danger of seasonal movement causing problems. Lon Schleining in his FWW bench article (which was my inspiration for this bench) and the instructions that came with my Lee Valley vise used a method similar to that used to attach breadboard ends. Like those, I milled a tenon on the end of bench and a slot on the back of the apron. They recommended attaching the apron with machine bolts in counterbores and barrel nuts buried in the table. Then they plugged the bolt head holes. I had two problems with that- appearance and the inability to tighten the bolts and snug up the apron at a later date. My solution was to bury barrel nuts in the apron, use 1/4-20 all-thread rod in a 3/8" hole (to allow movement), and pull it all tight with a nut and washer in a pocket in the underside of the table. It worked great!:
No visible hole plugs covering bolt heads:
http://www.ncwoodworker.net/pp/data/...m/IMG_2948.jpg
A view under the table. The hole on the left is for the barrel nut. A nut and washer is installed on the all thread rod in the pocket at right. I drilled three close holes and chiseled away the remaining wood to make the pockets. If I had a small ratcheting box wrench I could have made the pockets smaller. I can easily pull the aprons very tight this way:
http://www.ncwoodworker.net/pp/data/...m/IMG_2952.jpg
I am using 3/4" round Lee Valley Bench Dogs and Pups. When I laid out the locations for my dog holes I was very careful to avoid the locations of vise hardware and bench structure. I made a drill guide on my drill press and used it to keep and electric hand drill perpendicular while drilling holes in the top of the table and the aprons. I drilled the holes in the vise jaws on the drill press. Once I had one row completed I was able to use my Gramercy holdfasts to help clamp the guide:
http://www.ncwoodworker.net/pp/data/.../IMG_29101.jpg
http://www.ncwoodworker.net/pp/data/.../IMG_29171.jpg
http://www.ncwoodworker.net/pp/data/.../IMG_29201.jpg
After some serious planing, scraping and sanding, the bench was finished with a 60/40 mix of mineral spirits and marine varnish. I will probably knock down the gloss of the top with steel wool or a Scotchbrite pad, then give it a few coats of wax. The bench is at its lowest height (30") here:
http://www.ncwoodworker.net/pp/data/...m/IMG_2931.jpg
And its highest (43") here:
http://www.ncwoodworker.net/pp/data/...m/IMG_2934.jpg
The quick release front vise (r.) and sliding tail vise (l.). I used my lathe to turn the vise handles out of scrap maple. The end knobs came from the local Michaels craft store.
http://www.ncwoodworker.net/pp/data/...m/IMG_2943.jpg
http://www.ncwoodworker.net/pp/data/...m/IMG_2954.jpg
The adjustable legs are a variation of those I designed for my assembly table. I added a small pedal to release the ratchet pawls when I lower the table. I am not completely satisfied with the pedal arrangement and may change it. The bench is heavy, but changing height is not too bad. It is something that I won't be doing often once I find a comfortable working height, but if I need it, I have that capability.
http://www.ncwoodworker.net/pp/data/...m/IMG_2955.jpg
http://www.ncwoodworker.net/pp/data/...m/IMG_2956.jpg
The finishing touch is a label Rob Lee of Lee Valley graciously sent me along with some cork vise facing. I put the label on the chain cover I made for my custom Lee Valley/Veritas Twin Screw Vise installation. Thanks Rob!
http://www.ncwoodworker.net/pp/data/...m/IMG_2939.jpg
Clever design of the legs
At first glance, I'd think that it would tend to rack quite a bit back and forth under pressure, particularly since the load is on the narrow inner legs.
However, after looking at it closer, I see how you designed the inner legs so they nest inside the outer ones with the arrow head shaped profile.
I'm gonna guess that profile, coupled with the design of the bars/bracket that meshes with the teeth forces the inner legs out towards the outer ones and eliminates any racking.
Are my guesses correct? If so, very clever design. I'm impressed!!!!
Regards,
John