View Profile: Steve Schlumpf - Sawmill Creek Woodworking Community

Yesterday, 11:08 PM

Bruce Page replied to a thread Ship-lap in General Woodworking and Power Tools

I’ve only done ship lap once (actually spline & groove) and probably didn’t do it right. I screwed each piece into a rabbit. We don’t have many...

13 replies | 538 view(s)

Yesterday, 7:56 PM

Bruce Page replied to a thread Thickness planer board return ideas in General Woodworking and Power Tools

Brilliant! Beautiful planer Jeff. Jealous!

8 replies | 270 view(s)

Yesterday, 7:29 PM

Jim Becker replied to a thread BLO Dry Time in Project Finishing

Always good to test as I noted because yes, some species benefit with the oil vs just the oil based finish. For those of us that don't use oil based...

6 replies | 102 view(s)

Yesterday, 5:11 PM

Jim Becker replied to a thread Thickness planer board return ideas in General Woodworking and Power Tools

Greg beat me to it...HDPE strips or a sheet and it doesn't have to be real thick and raise the boards up a lot as rollers would.

8 replies | 270 view(s)

Yesterday, 5:05 PM

Jim Becker replied to a thread BLO Dry Time in Project Finishing

The next day is fine if you did the wipe off as noted. But do consider that you're going to get about the same effect from the first coat of an oil...

6 replies | 102 view(s)

Yesterday, 4:18 PM

Bruce Page replied to a thread RIP David Charlesworth in Off Topic Forum

Sad news, RIP. David will be missed by many.

4 replies | 202 view(s)

Yesterday, 3:57 PM

Prashun Patel replied to a thread BLO Dry Time in Project Finishing

Until the surface has no tackiness. You just put on a thin coat and wiped most of it off right?

6 replies | 102 view(s)

Yesterday, 1:04 PM

Jim Becker replied to a thread Shop Build...should be a fun journey... in WorkShops

TIME TO BREAK GROUND for the new shop building. My permit is approved and I just have to pick it up (and pay for it) when it physically reaches the...

202 replies | 18034 view(s)

Yesterday, 12:59 PM

Jim Becker replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Busy can be a blessing, Dennis. :) This past week has been a mish-mash of landscaping and getting started on a quick laundry room remodel. We...

2 replies | 123 view(s)

Yesterday, 12:51 PM

Jim Becker replied to a thread Which way do shelf brackets go? in Off Topic Forum

I agree with Andy...I'd choose the long leg vertical for more weight under a narrower shelf and short leg vertical for a wider shelf for bigger bulk...

9 replies | 436 view(s)

Yesterday, 12:46 PM

Jim Becker replied to a thread Harvey Slider on Unisaw? in General Woodworking and Power Tools

Oh, I wasn't saying that the responses you got were appropriate...they were not and customers deserve better, especially from someone who is supposed...

20 replies | 723 view(s)

Yesterday, 12:41 PM

Keith Outten replied to a thread New to DelMarVa in General Woodworking and Power Tools

Welcome to the right coast! I was in your neighborhood last Wednesday, passing though from VA to New Jersey and return.

3 replies | 383 view(s)

Yesterday, 12:33 PM

Keith Outten replied to a thread Volkswagon Mechanics Talk To Me in Off Topic Forum

I acquired a 1976 Beetle from a friend of mine last week. I have not had the time to look very close at the car yet but it came from New Jersey so...

48 replies | 6444 view(s)

Yesterday, 12:26 PM

Prashun Patel replied to a thread RIP David Charlesworth in Off Topic Forum

Oh my. I had no idea. What a loss. I owned his sharpening dvd's which were my foundation. I respect him greatly. RIP.

4 replies | 202 view(s)

Yesterday, 12:18 PM

Keith Outten replied to a thread Volkswagon Mechanics Talk To Me in Off Topic Forum

Thanks Rick, I appreciate your efforts and understand completely how things disappear over time :)

48 replies | 6444 view(s)

Yesterday, 11:56 AM

John K Jordan replied to a thread Nailed It! in Off Topic Forum

I recently had trouble removing some stapled barbed wire even with the fence pliers shown. (A neighbor stapled to trees about 3' over the line -...

21 replies | 565 view(s)

Yesterday, 11:07 AM

Dennis Peacock started a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

23 May 2022 Greetings, Yes, I'm running way behind on getting this posted!!!! Sorry, but life, work and family have consumed a LOT of my days...

2 replies | 123 view(s)

Yesterday, 10:16 AM

Lee Schierer replied to a thread Looking for plans for geometric end table in Design Forum

I use a program called DoubleCad XT5, which is free. It isn't hard to learn, but it does take practice to get quick. The nice thing is that you can...

11 replies | 302 view(s)

Yesterday, 9:45 AM

Dave Anderson NH replied to a thread Time for some levity in Off Topic Forum

A few for fun.

2077 replies | 289970 view(s)

Yesterday, 9:16 AM

Lee Schierer replied to a thread Looking for plans for geometric end table in Design Forum

Actually you are quite correct. Thanks for checking my work.The two short boards were in fact not parallel. I should have picked up on the...

11 replies | 302 view(s)

Yesterday, 9:06 AM

Jim Becker replied to a thread Harvey Slider on Unisaw? in General Woodworking and Power Tools

I think that the miter slot comment came from the CSR thinking that the "sliding table" was their miter fence product which does use the slot...some...

20 replies | 723 view(s)

05-24-2022, 7:33 PM

John K Jordan replied to a thread Nailed It! in Off Topic Forum

I keep a supply of the 12” galvanized nails on hand. One great use is to hold stall mats in place. Put a large fender washer on some nails and...

21 replies | 565 view(s)

05-24-2022, 5:41 PM

Jim Becker replied to a thread Nailed It! in Off Topic Forum

There are special fencing pliers available that are very helpful with that removal task...example:

21 replies | 565 view(s)