View Profile: Mike Null - Sawmill Creek Woodworking Community

07-04-2022, 1:08 PM

Keith Outten replied to a thread And POOF! It Was Gone! in Off Topic Forum

I will do my best to review the thread in question again and restore it if possible but not on the 4th of July as I have other activities that I must...

43 replies | 1931 view(s)

07-03-2022, 6:34 AM

Keith Outten replied to a thread tracing a camera shadow projected on the drawing board in Laser Engraving General Topics

Nice job Stan.

4 replies | 237 view(s)

07-02-2022, 10:04 PM

Keith Outten replied to a thread Welding New Mig in Metalworking

My situation is similar to yours John except I still can't pass my own weld inspection :) I upgraded my cheap metal cutting band saw to a really...

44 replies | 11833 view(s)

07-02-2022, 9:45 PM

Keith Outten replied to a thread 3D Scanning Service - Check This out in CNC Machines

Brady Watson is a serious professional in his field and one of the nicest guys you could ever meet. My first professional experience with his company...

6 replies | 634 view(s)

07-02-2022, 6:05 PM

Bruce Page replied to a thread Mesh network question. in Off Topic Forum

Ditto. I have a drawer full of extender gadgets. I installed the Orbi mesh last year and it hasn't hiccuped once. I was lucky to get 3 bars (usually...

17 replies | 724 view(s)

07-02-2022, 1:33 PM

Bruce Page replied to a thread Oops, I have rust in my air compressor tank! in General Woodworking and Power Tools

....Yikes!

26 replies | 1659 view(s)

07-02-2022, 9:02 AM

Keith Outten replied to a thread Welding New Mig in Metalworking

Yo Jack, that's good advice. I worked with hundreds of the best welders in this country when I was a young man so I appreciate your input. I was a...

44 replies | 11833 view(s)

07-02-2022, 7:54 AM

Keith Outten replied to a thread Tear Drop WIP in Turner's Forum

Bruce, It's a beautiful design and amazing craftsmanship. It's must be well balanced to stand on such a small flat area of the base. Thanks for...

43 replies | 4132 view(s)

07-01-2022, 10:59 PM

Bruce Page replied to a thread Time for some levity in Off Topic Forum

And so it goes..

2212 replies | 322708 view(s)

07-01-2022, 12:34 PM

Bruce Page replied to a thread Gassed up today in Off Topic Forum

That's not the case at the Costco I buy from. When I filled up on Tuesday Reg was $4.29 and Premium was 70 cents higher at $4.99. I don't remember...

126 replies | 12586 view(s)

07-01-2022, 8:10 AM

Keith Outten replied to a thread Volkswagon Mechanics Talk To Me in Off Topic Forum

Question - Does anyone know if the steering column from the 1976 Beetle will fit my 1967 VW? The newer steering column has turn signals,...

49 replies | 8260 view(s)

06-29-2022, 5:29 PM

Bruce Page replied to a thread Oops, I have rust in my air compressor tank! in General Woodworking and Power Tools

I agree with Tom, it’s not a huge problem. That said, I added an automatic drain valve (ADV) to my compressor and have been rust free ever since. The...

26 replies | 1659 view(s)

06-29-2022, 12:28 PM

Keith Outten started a thread 3D Scanning Service - Check This out in CNC Machines

If you own a CNC Router you will definitely be interested in visiting this web site even if your just cruising the Net looking for some interesting...

6 replies | 634 view(s)

06-28-2022, 5:03 PM

Keith Outten replied to a thread what kind of clear plastic to use in kitchen in General Woodworking and Power Tools

Dave, I don't think that I have a chisel that is as sharp as you guys prefer them to be so my test wouldn't be a valuable comparison :) I do have a...

35 replies | 2393 view(s)

06-27-2022, 6:55 PM

Bruce Page replied to a thread Time for some levity in Off Topic Forum

Adding a few more

2212 replies | 322708 view(s)

06-27-2022, 10:48 AM

Keith Outten replied to a thread Material Cart/Assembly Table/MFT -- RUWI Inspired in WorkShops

My new motorcycle lift uses compressed air so there is no fluid to be concerned with. It also has a series of mechanical locks at various heights to...

14 replies | 1162 view(s)

06-27-2022, 10:37 AM

Keith Outten replied to a thread what kind of clear plastic to use in kitchen in General Woodworking and Power Tools

Solid surface material is not a soft plastic which would not be an acceptable material for a cutting board. I have made hundreds of Corian cutting...

35 replies | 2393 view(s)

06-26-2022, 9:06 AM

Keith Outten replied to a thread what kind of clear plastic to use in kitchen in General Woodworking and Power Tools

Solid Surface cutting boards are an option for some people and are available in a variety of colors. Any shape or size and all you need is a router...

35 replies | 2393 view(s)

06-26-2022, 8:27 AM

Keith Outten replied to a thread Material Cart/Assembly Table/MFT -- RUWI Inspired in WorkShops

A big two thumbs up from me Mike, I am a huge fan of hydraulic tables and yours is very versatile. What are the size of the holes in your table and...

14 replies | 1162 view(s)

Mike Null
Moderator

Mini Statistics

More 15 Friends

Andy Hoyt

Clem Harriss

Keith Winter

Michael J Evans

Jarami Reid

Albert Aguilar

Join Groups 1 Groups

Trotec Laser Engravers Users Group

Join Groups 0 Permission Groups

Recent Visitors

2 Visitor Messages

Basic Information

About Mike Null

Signature

Contact

Statistics

Total Posts

Visitor Messages

General Information

15 Friends

Albert Aguilar

Amie McGee

Andy Hoyt

Bruce Page

Chris Padilla

Clem Harriss

Edward Henry

Eric Burke

Jarami Reid

Josh Stephens

Mike Null Moderator

Mini Statistics

More 15 Friends

Join Groups 1 Groups

Join Groups 0 Permission Groups

Recent Visitors

2 Visitor Messages

Basic Information

About Mike Null

Signature

Contact

Statistics

Total Posts

Visitor Messages

General Information

15 Friends

Mike Null
Moderator