View Profile: John C Bush - Sawmill Creek Woodworking Community

Tab Content: All; John C Bush; Friends; Photos

Older Activity
Yesterday, 4:34 PM

John C Bush replied to a thread Self stacking outfeed for TS? in WorkShops

Hi Bryan, The Mag switch mount would work great. They weren't on my radar when I drilled the hole in my table buit would use them now.

see more

36 replies | 1275 view(s)
Yesterday, 11:45 AM

John C Bush replied to a thread is this a decent buy for $100? in General Woodworking and Power Tools

I had a WT shaper that I planned to restore and I found a WT guy that had lots of info on parts, restorations, etc.--not sure if it was a full time...

see more

6 replies | 326 view(s)
03-05-2021, 12:37 PM

John C Bush replied to a thread Walls... in WorkShops

Hi Andrew, I built my stand alone shop using barn beams from our old barn and used slot(slat?) wall panels for all the interior sheeting. I had a...

see more

31 replies | 2139 view(s)
02-28-2021, 2:41 PM

John C Bush replied to a thread Self stacking outfeed for TS? in WorkShops

I just read the new posts and the baby feeder is the one I have. It is easy to adjust and you do "aim" the feeder slightly toward the fence. I...

see more

36 replies | 1275 view(s)
02-28-2021, 2:21 PM

John C Bush replied to a thread Self stacking outfeed for TS? in WorkShops

I put a large "Brute" trash barrel at the end of my outfeed table to catch the "train" of milled pieces as I mill them. I can concentrate on the...

see more

36 replies | 1275 view(s)
02-28-2021, 1:46 PM

John C Bush replied to a thread Cyclone outside venting in WorkShops

Hi Dan, I have a 2hp cyclone in an attached shed, 55 gal drum to collect the swarf, I leave the dust bag off the bottom of the filter and leave a...

see more

38 replies | 1551 view(s)
02-19-2021, 6:46 PM

John C Bush replied to a thread Incra Miter Gauge in General Woodworking and Power Tools

Hi Rich, It is great for making accurate, repetitive cuts--especially for small parts, and for getting panels squared easily. . I was going to build...

see more

26 replies | 1794 view(s)
02-19-2021, 1:04 PM

John C Bush replied to a thread Incra Miter Gauge in General Woodworking and Power Tools

I have the 5000 miter sled and it is simple to use, very accurate, easy to store and put on the saw table( relative to a large DIY type sled). I...

see more

26 replies | 1794 view(s)
02-08-2021, 12:45 AM

John C Bush replied to a thread Is Titebond Best for This Application, Or Another Adhesive? (Please see photos) in General Woodworking and Power Tools

3M #77 Spray adhesive should work. Seems to stick most anything together-- 70 rpm's for sure-- and you can peel apart with a heat gun. It would shred...

see more

14 replies | 642 view(s)
02-05-2021, 2:01 PM

John C Bush replied to a thread Planer without jointer — doable? in General Woodworking and Power Tools

I use a torsion box sled to flatten stock too wide for my jointer. Cedar shims and a hot glue gun hold it just fine. I used 1/2" MDF for skins and...

see more

33 replies | 1038 view(s)

No More Results

John C Bush
Friend of the Creek

Mini Statistics

Recent Visitors

2 Visitor Messages

Basic Information

About John C Bush

Statistics

Total Posts

Visitor Messages

General Information

John C Bush Friend of the Creek

Mini Statistics

Recent Visitors

2 Visitor Messages

Basic Information

About John C Bush

Statistics

Total Posts

Visitor Messages

General Information

John C Bush
Friend of the Creek