Register
Help
Remember Me?
What's New?
Forum
New Posts
FAQ
Calendar
Community
Groups
Albums
Member List
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Articles
Blogs
Donate
Sponsors
Friends of the Creek
Advanced Search
Member List
Jamie Buxton
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Jamie Buxton
Contributor
Home Page
Find latest posts
Find latest started threads
View Articles
View Blog Entries
Mini Statistics
Join Date
03-07-2003
Last Activity
Today
4:09 PM
Blog Entries
0
More
1
Friend
Harold Patterson
Recent Visitors
The last 10 visitor(s) to this page were:
Charlie Velasquez
,
Fred Perreault
,
Harold Patterson
,
Mel Fulks
,
Randall Pitts
,
Rob Sack
,
Ron Citerone
,
scott lipscomb
,
Steve Jenkins
,
vince mastrosimone
This page has had
38,154
visits
Tab Content
Jamie Buxton's Activity
About Me
Friends
Tab Content
All
Jamie Buxton
Friends
Photos
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
05-31-2023,
7:07 PM
Jamie Buxton
replied to a thread
Upward opening cabinet door
in
Design Forum
I've used this Blum one. ...
see more
2 replies | 370 view(s)
05-27-2023,
7:05 PM
Jamie Buxton
replied to a thread
Workbench retrofit
in
WorkShops
A benefit of the beam saw is that you never have to move that monster slab. And you never have to flip it either. The bench just stands there while...
see more
19 replies | 1326 view(s)
05-27-2023,
7:00 PM
Jamie Buxton
replied to a thread
Workbench retrofit
in
WorkShops
Rather than an expensive track saw, use a budget equivalent. Fasten your own straightedge to the bench top. Use it as guide for a circular saw....
see more
19 replies | 1326 view(s)
05-27-2023,
5:36 PM
Jamie Buxton
replied to a thread
Workbench retrofit
in
WorkShops
One more process you might consider is hand planing. The tilted surface is probably not far off 90 degrees, which means you’re not removing much...
see more
19 replies | 1326 view(s)
05-23-2023,
3:38 PM
Jamie Buxton
replied to a thread
Cutting Corian
in
General Woodworking and Power Tools
I’ve cut coriander with a standard carbide saw blade, and formed an edge with a standard carbide-tipped router bit.
see more
12 replies | 1021 view(s)
05-21-2023,
3:16 PM
Jamie Buxton
replied to a thread
When template routing does it matter where the bearing is?
in
General Woodworking and Power Tools
If you out the template on top, and manage to tip the router, you gouge the workpiece. If you put the template on the bottom , that doesn’t happen.
see more
14 replies | 1275 view(s)
05-17-2023,
5:07 PM
Jamie Buxton
replied to a thread
Curved legs for table
in
General Woodworking and Power Tools
Cut the joinery before you do the bandsawing. That gives you flat reference surfaces.
see more
3 replies | 396 view(s)
05-17-2023,
5:06 PM
Jamie Buxton
replied to a thread
Curved legs for table
in
General Woodworking and Power Tools
Yeah, bandsaw close, then good rasps to clean up and round over edges.
see more
3 replies | 396 view(s)
05-14-2023,
11:46 AM
Jamie Buxton
replied to a thread
Gas can frustrations
in
Off Topic Forum
I followed William's suggestion, and bought a replacement nozzle off Amazon. The nozzle came a collection of parts. There was a nozzle, two collars...
see more
31 replies | 3637 view(s)
05-12-2023,
5:50 PM
Jamie Buxton
replied to a thread
Drawer depth vs width using ball bearing slides
in
General Woodworking and Power Tools
Actually, there are metal slides which do what you describe. Accursed makes them, and others might too.
see more
15 replies | 1259 view(s)
05-12-2023,
10:30 AM
Jamie Buxton
replied to a thread
Best low-maintenance finish for outdoor bench
in
Project Finishing
Why would a mildewicide be a bad thing indoors?
see more
31 replies | 2998 view(s)
05-08-2023,
10:43 PM
Jamie Buxton
replied to a thread
Screws into ash end grain??
in
General Woodworking and Power Tools
It is true: screws into end grain don't hold as well as in to face grain. Notice the "as well" in the middle? Use longer screws.
see more
14 replies | 1079 view(s)
05-08-2023,
11:14 AM
Jamie Buxton
replied to a thread
Gas can frustrations
in
Off Topic Forum
Have you bought one? Does it work well? Brand name?
see more
31 replies | 3637 view(s)
05-07-2023,
11:13 PM
Jamie Buxton
started a thread
Gas can frustrations
in
Off Topic Forum
I spent a good fifteen minutes today wrestling with a new-fangled gas can. The thing is mandated by the government to be child-proof and...
see more
31 replies | 3637 view(s)
05-06-2023,
11:28 AM
Jamie Buxton
replied to a thread
Router use safety
in
General Woodworking and Power Tools
The issue with handheld use of that big bit is that the router may tip. The bit cuts so far away from the bearing that there's not much surface for...
see more
22 replies | 2060 view(s)
More Activity
No More Results
No Recent Activity
About Jamie Buxton
Basic Information
About Jamie Buxton
Location:
San Francisco, CA
Contact
This Page
https://sawmillcreek.org/member.php?810-Jamie-Buxton&s=34b53570e1de73c7dff902595ec82da4
Statistics
Total Posts
Total Posts
10,109
Posts Per Day
1.37
General Information
Last Activity
Today
4:09 PM
Join Date
03-07-2003
Home Page
http://www.jamiebuxton.com
1
Friend
Harold Patterson
Contributor
Showing Friends 1 to 1 of 1
Home Page
Find latest posts
View Articles
View Blog Entries