No Recent Activity

10 Visitor Messages

  1. View Conversation
    Hi Joe
    I'm tuning up an Scmi f3a and came across your post. Wondering if you had any problem adjusting the eccentric bushings to adjust the tables to coplaner? Mine are stuck solid. My unit is 40 years old so perhaps age as got them sticking but hoping there's a simple fix rather than taking the whole machine apart. Any ideas? Thanks much!
  2. View Conversation
    Joe -

    Clarification on my Sketchup model: I actually ordered the 80" length. The model depicts the full +/- wagon travel, not the static wagon size. I found this easier to use in laying out the shop.

    You mentioned earlier that you liked the high-speed router spindle. My local sales rep (Carl) does not recommend this spindle, but it seems like a good idea to me. Do you actually prefer using this spindle to a dedicated router station, or do you have a separate router table also?
    Did you order a power-feeder for the shaper? If so, which model do you recommend? Please send a list of recommended shaper and saw options.

    Thanks again for your help.
  3. I do have the precision adjust on the rip fence, but I've only used the rip fence a few times. One of the biggest improvements I've made is air clamps. Several on the FOG have "Big Squeeze" clamps. They were invented and productized by Brian Lamb. He later sold the design and rights to another company. Apparently that company is not building them now. Fortunately Brian lives in the Phoenix area and he was willing to show me how to make my own. I've attached some pics. I also built my own parallel cutting jig.

    In looking at your sketchup model, it looks like your slider won't have enough travel. I think the travel on mine with a 9 ft slider is 22 ft. You'll need double the slide length plus 18-24", or about 180-184". I ended up putting the slider more on a wall so I wouldn't have to walk around it all the time. I know some guys put it at an angle in the shop to so they don't have to walk around it so much.
  4. View Conversation
    Joe -

    Thanks for the replies below. I am about to place my order for the KF700S: 1100 outrigger and 31" rip since I've limited space in the garage. The slider is 80" - should be fine for nearly all of my work and I can still plan to use the Festool for the occassional full-sheet rip.

    Interesting comments about the router spindle, since I have a router built into the extension on my current contractor saw and I would like to avoid a separate router table if possible. A sketchup model of my shop setup is available at

    I was planning to order the fine-adjust, 31" rip fence. Do you think that's worthwhile, or should I just ignore any rip fence upgrades? I have the Incra fence now and love it, but I'm hoping to repurpose it as a parallel rip guide similar to that used by Sam Blasco. Your thoughts?

    Thanks again,
  5. View Conversation
    Hello Joe -

    I am considering the purchase of the KF700S and saw that you have a KF700SP. Since virtually everything from Felder is optional, what "options" do you consider most worthwhile now that you've had your system for a while? For instance, should I spring for the power feeder immediately and is the standard 80" slider too short?

    Thanks in advance.
  6. View Conversation
    Mr. Jensen,
    I am looking to buy a Delta No. 34-1172 tenon jig. I have noticed that you sold one a while back. I am finding a Delta number tenon jig 34-172 liisted on the internet. Can you tell me if this is the same jig as the one you sold or a newer model? Any information would be helpful.
  7. View Conversation
    I want to buy your powermatic spindle off you.
    Will you e-mail me
  8. View Conversation
    I am very interested in the powermatic shaper spindle that you have. I would like to take to you about it. Please call me as soon as possible. My cell phone number is 715-556-0087.

    Thank you,

    Dave Clark
  9. View Conversation
    Hello Joe,
    I have been looking for a Porter Cable 5361 Router base for the Porter Cable 5362 Speedmatic Router and I stumbled upon your posting on this site from 11-08-2008 where you stated you had four of these bases. I read that you were using a few of them and was wondering if you would be interested in selling just one of them. I 'd like to purchase it from you if you'd be so inclined. Please let me know. Thanks for your consideration,
  10. View Conversation
    Joe, I am interested in the terminus cutter head you've got for the Powermatic 60. Is the 5/8" shaft the standard for the PM 60?

    Is this a straight forward replacement for the stock cutter head? Does it come with instructions?


Showing Visitor Messages 1 to 10 of 10
About Joe Jensen

Basic Information

About Joe Jensen
Phoenix AZ Area
WW, Photography, building


Total Posts
Total Posts
Posts Per Day
Visitor Messages
Total Messages
Most Recent Message
05-10-2016 3:15 PM
General Information
Last Activity
04-24-2023 2:39 PM
Join Date

3 Friends

  1. Allan Grant Allan Grant is offline


    Allan Grant
  2. Rick Fisher Rick Fisher is offline


    Rick Fisher
  3. Tim Ulmen Tim Ulmen is offline


    Tim Ulmen
Showing Friends 1 to 3 of 3