View Profile: Bruce King - Sawmill Creek Woodworking Community

Tab Content: All; Bruce King; Friends; Photos

Older Activity
04-17-2021, 4:51 PM

Bruce King replied to a thread Lightning Protection in WorkShops

The two best things to do, install a surge device that plugs into both legs in the main panel. Add another copper ground rod at least 8 feet from...

see more

20 replies | 831 view(s)
04-05-2021, 12:33 AM

Bruce King replied to a thread Cutting Board for my Wife in Woodworking Projects

Very cool! One of those designs that makes me wonder why I didn’t think of it.

see more

4 replies | 563 view(s)
04-05-2021, 12:19 AM

Bruce King replied to a thread Straight line rip on TS before jointing face and one edge in General Woodworking and Power Tools

I had planned to post about that same technique and also do some light planing before face jointing saves a lot of effort and wear on the more...

see more

19 replies | 1317 view(s)
04-03-2021, 3:15 PM

Bruce King replied to a thread nice work chair around the shop and house. in WorkShops

Have a picture? I have a short stool on my list to build.

see more

12 replies | 1075 view(s)
03-29-2021, 9:41 PM

Bruce King replied to a thread Yikes! Just got an estimate to refinish my porch in Off Topic Forum

A neighbor replaced his porch steps with IPE. Looks very nice. Also known as Brazilian walnut.

see more

15 replies | 1242 view(s)
03-29-2021, 9:34 PM

Bruce King replied to a thread Yikes! Just got an estimate to refinish my porch in Off Topic Forum

If you are in a neighborhood you can get on the Nextdoor app and get local labor easily. Around here we have some motivated teenagers and even their...

see more

15 replies | 1242 view(s)
03-25-2021, 12:03 PM

Bruce King replied to a thread Vaccination Arm in Off Topic Forum

We got the J and J for several reasons, it’s hard to find an appointment here for anything, it’s 100 percent effective at keeping you out of the...

see more

39 replies | 3008 view(s)
03-24-2021, 12:21 AM

Bruce King replied to a thread 3 phase motors running in reverse suddenly - help in General Woodworking and Power Tools

While it’s working check the 3 phase output from the RPC again and write it down for future reference.

see more

14 replies | 1302 view(s)
03-24-2021, 12:09 AM

Bruce King replied to a thread China hutch door warped. Help in General Woodworking and Power Tools

Whatever you decide don’t forget that it must be tempered glass. Leave space for the wood to move without breaking the glass.

see more

16 replies | 767 view(s)
03-23-2021, 11:04 AM

Bruce King replied to a thread Wanna make the wife happy? This project is for you in Woodworking Projects

Very nice but if building a kitchen think about a pantry cabinet, 30 to 36 wide with slideouts. We have the top one close to top of the lower...

see more

19 replies | 2008 view(s)
03-23-2021, 10:45 AM

Bruce King replied to a thread 220V Tools & Extension Cords in General Woodworking and Power Tools

Extension cords are not to be used on a permanent situation except tools that don’t run for hours at a time. 5hp tools really should have an...

see more

24 replies | 1357 view(s)
03-23-2021, 10:36 AM

Bruce King replied to a thread A Physics Question in Off Topic Forum

This shows more detail http://saxbyphysics.com/AdvancedPhysicsLab/Mechanics/Gravity/UniversalGravitationalPotentialEnergy.pdf

see more

23 replies | 1183 view(s)

No More Results

Bruce King
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Bruce King

Statistics

Total Posts

General Information

Bruce King Contributor

Mini Statistics

Recent Visitors

Basic Information

About Bruce King

Statistics

Total Posts

General Information

Bruce King
Contributor